Acer M11E manual Mmmmssssooo Wxxxx

Page 46

Table 1-4

System Error Messages

 

 

 

 

 

 

 

 

 

 

 

Message

 

Action

 

 

Memory Error at:

Check DIMMs on the system

 

 

MMMM:SSSS:OOO (W:XXXX,

board. Contact your dealer.

 

 

R:YYYY)

 

 

 

 

 

 

where:

 

 

 

 

 

 

M: MB, S: Segment,

 

 

 

 

 

O: Offset,

 

 

 

 

 

 

X/Y: write/read pattern

 

 

 

 

 

 

 

 

 

Memory Size Mismatch

Check the memory size based

 

 

CPU Clock Mismatch

on the system specifications.

 

 

Check the internal cable

 

 

 

 

 

 

 

 

connections. If you are sure that

 

 

 

 

connections and values are

 

 

 

 

correct, ignore the message. If

 

 

 

 

the message reappears, ask for

 

 

 

 

technical assistance.

 

 

 

 

 

 

Onboard Serial Port 1 Conflict

Run Setup and disable the port.

 

 

 

 

 

 

Onboard Serial Port 2 Conflict

Run Setup and disable the port.

 

 

 

 

 

 

Onboard Parallel Port Conflict

Run Setup and disable the port.

 

 

 

 

 

 

Pointing Device Error

Check and connect pointing

 

 

 

 

device.

 

 

 

 

 

 

 

 

Pointing Device Interface

Replace the pointing device or

 

 

Error

 

contact your dealer.

 

 

 

 

 

 

 

 

 

Press F1 key to continue or

Press

or

 

 

 

Ctrl-Alt-Esc for Setup

+

+

to enter

 

 

 

 

Setup.

 

 

 

 

 

 

 

 

Real Time Clock Error

Run Setup and set the time and

 

 

 

 

date.

 

 

 

 

 

 

 

 

 

Press Esc to turn off NMI, any

Press

to disregard the NMI

 

 

key to reboot

error.

 

 

 

 

 

 

Press any other key to reboot the

 

 

 

 

system.

 

 

 

 

 

 

 

 

 

 

1-30

 

 

 

User’s Guide

Image 46
Contents M11E System Copyright Important Safety Instructions Page Page CD ROM Safety Warning Vii FCC Class B Radio Frequency Interference Statement About this Manual Purpose Manual StructureConventions Table of Contents Bios Utility XiiXiii List of Figures XivList of Tables Page Features System BoardUser’s Guide Major Components System Board Layout with Network Connector System Board LayoutSystem Board Layout without Network Connector Jumpers and Connectors Jumper and Connector LocationsBlackened pin of a jumper or connector represents pin Jumper Settings Connector FunctionsJP1 ESD Precautions Installing the Pentium II processor Attaching the Processor Fan SinkRemoving tape protector from Fan SInk Locking a Wide Clip End 10 Locking the metal bracket Installing a Pentium II Processor 11 Installing the Pentium II Retention Mechanism12 Installing the Pentium II Retention Mechanism 13 Installing a Pentium II Processor Removing a Pentium II Processor 14 Securing the Pentium II Processor16 Removing the Pentium II Processor Memory Upgrade Memory ConfigurationsInstalling a Dimm 17 Installing a DimmRemoving a Dimm 18 Removing a DimmReconfiguring the System Installing Expansion Cards Installing PCI CardsInstalling ISA Cards Bios detects and configures only PnP cardsInstalling an AGP Card 20 Installing an ISA Card21 Installing an AGP Card Software Error Messages Error MessagesSystem Error Messages System Board Mmmmssssooo Wxxxx Correcting Error Conditions Page Setup Utility Entering Setup Setup UtilitySetup Utility System Information Processor Speed ProcessorInternal Cache Size Floppy Drive B External CacheFloppy Drive a IDE Primary Channel MasterSerial Port IDE Secondary Channel SlaveTotal Memory Parallel Port15 PS/2 Mouse System S/N Product InformationProduct Name Main Board IDDMI Bios Version System Bios VersionMain Board S/N Disk Drives Floppy DrivesIDE Drives 2 LS-120 Drive Compatible AsIDE Primary Channel Master IDE Secondary Channel Master IDE Primary Channel SlaveIDE Secondary Channel Slave This parameter specifies the size of your hard disk, in MB Disabled Enhanced IDE FeaturesDMA Transfer Mode Serial Ports 1 Onboard PeripheralsBase Address ∙ 3BCh ∙ 378h ∙ 278h Onboard Device Settings Operation ModePS/2 Mouse Controller Floppy Disk ControllerIDE Controller USB Host ControllerSMBus Interrupt IRQ9 Onboard Ethernet ChipPower Management Mode Power ManagementIDE Hard Disk Standby Timer Modem Ring Indicator Power Switch 4 secSystem Sleep Timer System Wake-up EventBoot Options Boot SequenceSilent Boot Fast BootFirst Hard Disk Drive Boot from LANDesk Service Agent Num Lock After BootConfiguration Table Memory TestDate and Time DateTime Advanced Options Memory/Cache OptionsExternal Cache Internal Cache CPU CacheMemory at 15MB-16MB Reserved for 2 PnP/PCI Options Memory Parity ModeFor system board with LAN PCI IRQ Setting For system board without LANPCI IRQ Sharing VGA Palette SnoopGraphics Aperture Size Reset Resource AssignmentsCPU Frequency Plug and Play OSCPU Multiple Bus FrequencyProcessor Speed To set or change a Password Setup PasswordSystem Security Setup Utility To remove your Setup Password To bypass Setup Password Power-on Password Make sure to set JP3 to 1-2 to enable Power-on passwordDrive Control Settings Disk Drive ControlLoad Default Settings Abort Settings ChangeExit Setup