Acer M11E manual Date and Time

Page 75

2.8Date and Time

The real-time clock keeps the system date and time. After setting the date and time, you do not need to enter them every time you turn on the system. As long as the internal battery remains good (approximately seven years) and connected, the clock continues to keep the date and time accurately even when the power is off.

 

Boot Options

 

 

Date

............................... [Fri Jun 11,1998]

Time

............................... [HH:MM:SS]

 

 

2.8.1Date

Highlight the items on the Date parameter and press or to set the date following the weekday-month-day-year format.

Valid values for weekday, month, day, and year are:

Weekday

Sun, Mon, Tue, Wed, Thu, Fri, Sat

Month

1 to 12

Day

1 to 31

Year

1980 to 2099

Setup Utility

2-27

Image 75
Contents M11E System Copyright Important Safety Instructions Page Page CD ROM Safety Warning Vii FCC Class B Radio Frequency Interference Statement Manual Structure About this Manual PurposeConventions Table of Contents Xii Bios UtilityXiii Xiv List of FiguresList of Tables Page System Board FeaturesUser’s Guide Major Components System Board Layout System Board Layout with Network ConnectorSystem Board Layout without Network Connector Jumper and Connector Locations Jumpers and ConnectorsBlackened pin of a jumper or connector represents pin Connector Functions Jumper SettingsJP1 ESD Precautions Attaching the Processor Fan Sink Installing the Pentium II processorRemoving tape protector from Fan SInk Locking a Wide Clip End 10 Locking the metal bracket 11 Installing the Pentium II Retention Mechanism Installing a Pentium II Processor12 Installing the Pentium II Retention Mechanism 13 Installing a Pentium II Processor 14 Securing the Pentium II Processor Removing a Pentium II Processor16 Removing the Pentium II Processor Memory Configurations Memory Upgrade17 Installing a Dimm Installing a Dimm18 Removing a Dimm Removing a DimmReconfiguring the System Installing PCI Cards Installing Expansion CardsBios detects and configures only PnP cards Installing ISA Cards20 Installing an ISA Card Installing an AGP Card21 Installing an AGP Card Error Messages Software Error MessagesSystem Error Messages System Board Mmmmssssooo Wxxxx Correcting Error Conditions Page Setup Utility Setup Utility Entering SetupSetup Utility System Information Processor Processor SpeedInternal Cache Size IDE Primary Channel Master External CacheFloppy Drive a Floppy Drive BParallel Port IDE Secondary Channel SlaveTotal Memory Serial Port15 PS/2 Mouse Main Board ID Product InformationProduct Name System S/NSystem Bios Version DMI Bios VersionMain Board S/N Floppy Drives Disk Drives2 LS-120 Drive Compatible As IDE DrivesIDE Primary Channel Master IDE Primary Channel Slave IDE Secondary Channel MasterIDE Secondary Channel Slave This parameter specifies the size of your hard disk, in MB Enhanced IDE Features DisabledDMA Transfer Mode Onboard Peripherals Serial Ports 1Base Address ∙ 3BCh ∙ 378h ∙ 278h Operation Mode Onboard Device SettingsUSB Host Controller Floppy Disk ControllerIDE Controller PS/2 Mouse ControllerOnboard Ethernet Chip SMBus Interrupt IRQ9Power Management Power Management ModeIDE Hard Disk Standby Timer System Wake-up Event Power Switch 4 secSystem Sleep Timer Modem Ring IndicatorBoot Sequence Boot OptionsFast Boot Silent BootFirst Hard Disk Drive Memory Test Num Lock After BootConfiguration Table Boot from LANDesk Service AgentDate Date and TimeTime Memory/Cache Options Advanced OptionsInternal Cache CPU Cache External CacheMemory at 15MB-16MB Reserved for Memory Parity Mode 2 PnP/PCI OptionsFor system board with LAN For system board without LAN PCI IRQ SettingVGA Palette Snoop PCI IRQ SharingPlug and Play OS Reset Resource AssignmentsCPU Frequency Graphics Aperture SizeBus Frequency CPU MultipleProcessor Speed Setup Password To set or change a PasswordSystem Security Setup Utility To remove your Setup Password To bypass Setup Password Make sure to set JP3 to 1-2 to enable Power-on password Power-on PasswordDisk Drive Control Drive Control SettingsAbort Settings Change Load Default SettingsExit Setup