Acer M11E manual External Cache, Floppy Drive a, Floppy Drive B, IDE Primary Channel Master

Page 54

2.2.4External Cache

This parameter specifies the second-level cache memory size currently supported by the system. The available cache sizes are 256 KB or 512 KB (depending on the CPU installed). For information on how to configure the system memory, see section 2.9.1

2.2.5Floppy Drive A

This parameter specifies the system’s current diskette drive A settings. For information on how to configure the floppy drives, see section 2.4.1.

2.2.6Floppy Drive B

This parameter specifies the system’s current diskette drive B settings. For information on how to configure the floppy drives, see section 2.4.1.

2.2.7IDE Primary Channel Master

This parameter specifies the current configuration of the IDE device connected to the master port of the primary IDE channel. For information on how to configure the IDE drives, see section 2.4.3.

2.2.8IDE Primary Channel Slave

This parameter specifies the current configuration of the IDE device connected to the slave port of the primary IDE channel. For information on how to configure the IDE drives, see section 2.4.3.

2.2.9IDE Secondary Channel Master

This parameter specifies the current configuration of the IDE device connected to the master port of the secondary IDE channel. For information on how to configure the IDE drives, see section 2.4.3.

2-6	User’s Guide

Image 54

Contents M11E System Copyright Important Safety Instructions Page Page CD ROM Safety Warning Vii FCC Class B Radio Frequency Interference Statement About this Manual Purpose Manual StructureConventions Table of Contents Bios Utility XiiXiii List of Figures XivList of Tables Page Features System BoardUser’s Guide Major Components System Board Layout with Network Connector System Board LayoutSystem Board Layout without Network Connector Jumpers and Connectors Jumper and Connector LocationsBlackened pin of a jumper or connector represents pin Jumper Settings Connector FunctionsJP1 ESD Precautions Installing the Pentium II processor Attaching the Processor Fan SinkRemoving tape protector from Fan SInk Locking a Wide Clip End 10 Locking the metal bracket Installing a Pentium II Processor 11 Installing the Pentium II Retention Mechanism12 Installing the Pentium II Retention Mechanism 13 Installing a Pentium II Processor Removing a Pentium II Processor 14 Securing the Pentium II Processor16 Removing the Pentium II Processor Memory Upgrade Memory ConfigurationsInstalling a Dimm 17 Installing a DimmRemoving a Dimm 18 Removing a DimmReconfiguring the System Installing Expansion Cards Installing PCI CardsInstalling ISA Cards Bios detects and configures only PnP cardsInstalling an AGP Card 20 Installing an ISA Card21 Installing an AGP Card Error Messages Software Error MessagesSystem Error Messages System Board Mmmmssssooo Wxxxx Correcting Error Conditions Page Setup Utility Entering Setup Setup UtilitySetup Utility System Information Processor Processor SpeedInternal Cache Size Floppy Drive B External CacheFloppy Drive a IDE Primary Channel MasterSerial Port IDE Secondary Channel SlaveTotal Memory Parallel Port15 PS/2 Mouse System S/N Product InformationProduct Name Main Board IDSystem Bios Version DMI Bios VersionMain Board S/N Disk Drives Floppy Drives2 LS-120 Drive Compatible As IDE DrivesIDE Primary Channel Master IDE Primary Channel Slave IDE Secondary Channel MasterIDE Secondary Channel Slave This parameter specifies the size of your hard disk, in MB Disabled Enhanced IDE FeaturesDMA Transfer Mode Onboard Peripherals Serial Ports 1Base Address ∙ 3BCh ∙ 378h ∙ 278h Onboard Device Settings Operation ModePS/2 Mouse Controller Floppy Disk ControllerIDE Controller USB Host ControllerSMBus Interrupt IRQ9 Onboard Ethernet ChipPower Management Power Management ModeIDE Hard Disk Standby Timer Modem Ring Indicator Power Switch 4 secSystem Sleep Timer System Wake-up EventBoot Options Boot SequenceFast Boot Silent BootFirst Hard Disk Drive Boot from LANDesk Service Agent Num Lock After BootConfiguration Table Memory TestDate and Time DateTime Advanced Options Memory/Cache OptionsInternal Cache CPU Cache External CacheMemory at 15MB-16MB Reserved for Memory Parity Mode 2 PnP/PCI OptionsFor system board with LAN PCI IRQ Setting For system board without LANPCI IRQ Sharing VGA Palette SnoopGraphics Aperture Size Reset Resource AssignmentsCPU Frequency Plug and Play OSBus Frequency CPU MultipleProcessor Speed Setup Password To set or change a PasswordSystem Security Setup Utility To remove your Setup Password To bypass Setup Password Power-on Password Make sure to set JP3 to 1-2 to enable Power-on passwordDrive Control Settings Disk Drive ControlLoad Default Settings Abort Settings ChangeExit Setup