Acer M11E Power Switch 4 sec, System Wake-up Event, System Sleep Timer, Modem Ring Indicator

Page 71

System Sleep Timer

This parameter sets the system to the lowest power-saving mode after a specified period of inactivity. Any keyboard or mouse action or any activity detected from the IRQ channels resumes system operation.

SLEEP MODE

This parameter lets you specify the power-saving mode that the system will enter after a specified period of inactivity. The options are Standby and Suspend modes.

This parameter becomes configurable only if the System Sleep Timer is enabled. Any keyboard or mouse action, or any enabled monitored activities occurring through the IRQ channels resume system operation.

2.6.2Power Switch < 4 sec.

When set to Power Off, the system automatically turns off when the power switch is pressed for less than 4 seconds. When set to Suspend, the system enters the suspend mode when pressed for less than 4 seconds.

2.6.3System Wake-up Event

The system wake-up event allows the system to resume operation when the modem ring indicator is enabled.

Modem Ring Indicator

When Enabled any fax/modem activity wakes up the system from suspend mode. The default setting is Enabled.

Setup Utility

2-23

Image 71

Contents M11E System Copyright Important Safety Instructions Page Page CD ROM Safety Warning Vii FCC Class B Radio Frequency Interference Statement Manual Structure About this Manual PurposeConventions Table of Contents Xii Bios UtilityXiii Xiv List of FiguresList of Tables Page System Board FeaturesUser’s Guide Major Components System Board Layout System Board Layout with Network ConnectorSystem Board Layout without Network Connector Jumper and Connector Locations Jumpers and ConnectorsBlackened pin of a jumper or connector represents pin Connector Functions Jumper SettingsJP1 ESD Precautions Attaching the Processor Fan Sink Installing the Pentium II processorRemoving tape protector from Fan SInk Locking a Wide Clip End 10 Locking the metal bracket 11 Installing the Pentium II Retention Mechanism Installing a Pentium II Processor12 Installing the Pentium II Retention Mechanism 13 Installing a Pentium II Processor 14 Securing the Pentium II Processor Removing a Pentium II Processor16 Removing the Pentium II Processor Memory Configurations Memory Upgrade17 Installing a Dimm Installing a Dimm18 Removing a Dimm Removing a DimmReconfiguring the System Installing PCI Cards Installing Expansion CardsBios detects and configures only PnP cards Installing ISA Cards20 Installing an ISA Card Installing an AGP Card21 Installing an AGP Card System Error Messages Error MessagesSoftware Error Messages System Board Mmmmssssooo Wxxxx Correcting Error Conditions Page Setup Utility Setup Utility Entering SetupSetup Utility System Information Internal Cache Size ProcessorProcessor Speed IDE Primary Channel Master External CacheFloppy Drive a Floppy Drive BParallel Port IDE Secondary Channel SlaveTotal Memory Serial Port15 PS/2 Mouse Main Board ID Product InformationProduct Name System S/NMain Board S/N System Bios VersionDMI Bios Version Floppy Drives Disk DrivesIDE Primary Channel Master 2 LS-120 Drive Compatible AsIDE Drives IDE Secondary Channel Slave IDE Primary Channel SlaveIDE Secondary Channel Master This parameter specifies the size of your hard disk, in MB Enhanced IDE Features DisabledDMA Transfer Mode Base Address Onboard PeripheralsSerial Ports 1 ∙ 3BCh ∙ 378h ∙ 278h Operation Mode Onboard Device SettingsUSB Host Controller Floppy Disk ControllerIDE Controller PS/2 Mouse ControllerOnboard Ethernet Chip SMBus Interrupt IRQ9IDE Hard Disk Standby Timer Power ManagementPower Management Mode System Wake-up Event Power Switch 4 secSystem Sleep Timer Modem Ring IndicatorBoot Sequence Boot OptionsFirst Hard Disk Drive Fast BootSilent Boot Memory Test Num Lock After BootConfiguration Table Boot from LANDesk Service AgentDate Date and TimeTime Memory/Cache Options Advanced OptionsMemory at 15MB-16MB Reserved for Internal Cache CPU CacheExternal Cache For system board with LAN Memory Parity Mode2 PnP/PCI Options For system board without LAN PCI IRQ SettingVGA Palette Snoop PCI IRQ SharingPlug and Play OS Reset Resource AssignmentsCPU Frequency Graphics Aperture SizeProcessor Speed Bus FrequencyCPU Multiple System Security Setup PasswordTo set or change a Password Setup Utility To remove your Setup Password To bypass Setup Password Make sure to set JP3 to 1-2 to enable Power-on password Power-on PasswordDisk Drive Control Drive Control SettingsAbort Settings Change Load Default SettingsExit Setup