Acer M11E manual Installing a Pentium II Processor, Installing the Pentium II Retention Mechanism

Page 31

1.5.2Installing a Pentium II Processor

Follow these steps to install the Pentium II processor to the socket on the CPU board.

1a. Place the retention mechanism over the processor socket on the CPU board. Secure it with the screws that came with the package.

Figure 1-11 Installing the Pentium II Retention Mechanism

1b. Place the retention mechanism over the processor socket on the CPU board. Secure it with the plastic pegs that came with the package as shown below.

System Board

1-15

Image 31

Contents M11E System Copyright Important Safety Instructions Page Page CD ROM Safety Warning Vii FCC Class B Radio Frequency Interference Statement Manual Structure About this Manual PurposeConventions Table of Contents Xii Bios UtilityXiii Xiv List of FiguresList of Tables Page System Board FeaturesUser’s Guide Major Components System Board Layout System Board Layout with Network ConnectorSystem Board Layout without Network Connector Jumper and Connector Locations Jumpers and ConnectorsBlackened pin of a jumper or connector represents pin Connector Functions Jumper SettingsJP1 ESD Precautions Attaching the Processor Fan Sink Installing the Pentium II processorRemoving tape protector from Fan SInk Locking a Wide Clip End 10 Locking the metal bracket 11 Installing the Pentium II Retention Mechanism Installing a Pentium II Processor12 Installing the Pentium II Retention Mechanism 13 Installing a Pentium II Processor 14 Securing the Pentium II Processor Removing a Pentium II Processor16 Removing the Pentium II Processor Memory Configurations Memory Upgrade17 Installing a Dimm Installing a Dimm18 Removing a Dimm Removing a DimmReconfiguring the System Installing PCI Cards Installing Expansion CardsBios detects and configures only PnP cards Installing ISA Cards20 Installing an ISA Card Installing an AGP Card21 Installing an AGP Card Software Error Messages Error MessagesSystem Error Messages System Board Mmmmssssooo Wxxxx Correcting Error Conditions Page Setup Utility Setup Utility Entering SetupSetup Utility System Information Processor Speed ProcessorInternal Cache Size IDE Primary Channel Master External CacheFloppy Drive a Floppy Drive BParallel Port IDE Secondary Channel SlaveTotal Memory Serial Port15 PS/2 Mouse Main Board ID Product InformationProduct Name System S/NDMI Bios Version System Bios VersionMain Board S/N Floppy Drives Disk DrivesIDE Drives 2 LS-120 Drive Compatible AsIDE Primary Channel Master IDE Secondary Channel Master IDE Primary Channel SlaveIDE Secondary Channel Slave This parameter specifies the size of your hard disk, in MB Enhanced IDE Features DisabledDMA Transfer Mode Serial Ports 1 Onboard PeripheralsBase Address ∙ 3BCh ∙ 378h ∙ 278h Operation Mode Onboard Device SettingsUSB Host Controller Floppy Disk ControllerIDE Controller PS/2 Mouse ControllerOnboard Ethernet Chip SMBus Interrupt IRQ9Power Management Mode Power ManagementIDE Hard Disk Standby Timer System Wake-up Event Power Switch 4 secSystem Sleep Timer Modem Ring IndicatorBoot Sequence Boot OptionsSilent Boot Fast BootFirst Hard Disk Drive Memory Test Num Lock After BootConfiguration Table Boot from LANDesk Service AgentDate Date and TimeTime Memory/Cache Options Advanced OptionsExternal Cache Internal Cache CPU CacheMemory at 15MB-16MB Reserved for 2 PnP/PCI Options Memory Parity ModeFor system board with LAN For system board without LAN PCI IRQ SettingVGA Palette Snoop PCI IRQ SharingPlug and Play OS Reset Resource AssignmentsCPU Frequency Graphics Aperture SizeCPU Multiple Bus FrequencyProcessor Speed To set or change a Password Setup PasswordSystem Security Setup Utility To remove your Setup Password To bypass Setup Password Make sure to set JP3 to 1-2 to enable Power-on password Power-on PasswordDisk Drive Control Drive Control SettingsAbort Settings Change Load Default SettingsExit Setup