Acer M11E manual

Page 4

9.If an extension cord is used with this product, make sure that the total ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed 15 amperes.

10.Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

11.Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. Refer all servicing to qualified service personnel.

12.Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a.When the power cord or plug is damaged or frayed

b.If liquid has been spilled into the product

c.If the product has been exposed to rain or water

d.If the product does not operate normally when the operating instructions are followed, adjust only those controls that are covered by the operating instructions, since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition

e.If the product has been dropped or the cabinet has been damaged

f.If the product exhibits a distinct change in performance, indicating a need for service

iv

Image 4
Contents M11E System Copyright Important Safety Instructions Page Page CD ROM Safety Warning Vii FCC Class B Radio Frequency Interference Statement About this Manual Purpose Manual StructureConventions Table of Contents Bios Utility XiiXiii List of Figures XivList of Tables Page Features System BoardUser’s Guide Major Components System Board Layout with Network Connector System Board LayoutSystem Board Layout without Network Connector Jumpers and Connectors Jumper and Connector LocationsBlackened pin of a jumper or connector represents pin Jumper Settings Connector FunctionsJP1 ESD Precautions Installing the Pentium II processor Attaching the Processor Fan SinkRemoving tape protector from Fan SInk Locking a Wide Clip End 10 Locking the metal bracket Installing a Pentium II Processor 11 Installing the Pentium II Retention Mechanism12 Installing the Pentium II Retention Mechanism 13 Installing a Pentium II Processor Removing a Pentium II Processor 14 Securing the Pentium II Processor16 Removing the Pentium II Processor Memory Upgrade Memory ConfigurationsInstalling a Dimm 17 Installing a DimmRemoving a Dimm 18 Removing a DimmReconfiguring the System Installing Expansion Cards Installing PCI CardsInstalling ISA Cards Bios detects and configures only PnP cardsInstalling an AGP Card 20 Installing an ISA Card21 Installing an AGP Card Software Error Messages Error MessagesSystem Error Messages System Board Mmmmssssooo Wxxxx Correcting Error Conditions Page Setup Utility Entering Setup Setup UtilitySetup Utility System Information Processor Speed ProcessorInternal Cache Size External Cache Floppy Drive aFloppy Drive B IDE Primary Channel MasterIDE Secondary Channel Slave Total MemorySerial Port Parallel Port15 PS/2 Mouse Product Information Product NameSystem S/N Main Board IDDMI Bios Version System Bios VersionMain Board S/N Disk Drives Floppy DrivesIDE Drives 2 LS-120 Drive Compatible AsIDE Primary Channel Master IDE Secondary Channel Master IDE Primary Channel SlaveIDE Secondary Channel Slave This parameter specifies the size of your hard disk, in MB Disabled Enhanced IDE FeaturesDMA Transfer Mode Serial Ports 1 Onboard PeripheralsBase Address ∙ 3BCh ∙ 378h ∙ 278h Onboard Device Settings Operation ModeFloppy Disk Controller IDE ControllerPS/2 Mouse Controller USB Host ControllerSMBus Interrupt IRQ9 Onboard Ethernet ChipPower Management Mode Power ManagementIDE Hard Disk Standby Timer Power Switch 4 sec System Sleep TimerModem Ring Indicator System Wake-up EventBoot Options Boot SequenceSilent Boot Fast BootFirst Hard Disk Drive Num Lock After Boot Configuration TableBoot from LANDesk Service Agent Memory TestDate and Time DateTime Advanced Options Memory/Cache OptionsExternal Cache Internal Cache CPU CacheMemory at 15MB-16MB Reserved for 2 PnP/PCI Options Memory Parity ModeFor system board with LAN PCI IRQ Setting For system board without LANPCI IRQ Sharing VGA Palette SnoopReset Resource Assignments CPU FrequencyGraphics Aperture Size Plug and Play OSCPU Multiple Bus FrequencyProcessor Speed To set or change a Password Setup PasswordSystem Security Setup Utility To remove your Setup Password To bypass Setup Password Power-on Password Make sure to set JP3 to 1-2 to enable Power-on passwordDrive Control Settings Disk Drive ControlLoad Default Settings Abort Settings ChangeExit Setup