Acer M11E manual About this Manual Purpose, Manual Structure

Page 9

About this Manual

Purpose

This user’s guide aims to give you the information you need to operate the system properly and tells you how to install internal components.

Manual Structure

This user’s guide consists of two chapters.

Chapter 1

System Board

This chapter describes the system board and all its major components. It contains the system board layout, jumper settings, cache and memory configurations, and information on other internal devices.

Chapter 2

Setup Utility

This chapter gives information about the system BIOS and tells how to configure the system by changing the settings of the BIOS parameters.

ix

Image 9

Contents M11E System Copyright Important Safety Instructions Page Page CD ROM Safety Warning Vii FCC Class B Radio Frequency Interference Statement Manual Structure About this Manual PurposeConventions Table of Contents Xii Bios UtilityXiii Xiv List of FiguresList of Tables Page System Board FeaturesUser’s Guide Major Components System Board Layout System Board Layout with Network ConnectorSystem Board Layout without Network Connector Jumper and Connector Locations Jumpers and ConnectorsBlackened pin of a jumper or connector represents pin Connector Functions Jumper SettingsJP1 ESD Precautions Attaching the Processor Fan Sink Installing the Pentium II processorRemoving tape protector from Fan SInk Locking a Wide Clip End 10 Locking the metal bracket 11 Installing the Pentium II Retention Mechanism Installing a Pentium II Processor12 Installing the Pentium II Retention Mechanism 13 Installing a Pentium II Processor 14 Securing the Pentium II Processor Removing a Pentium II Processor16 Removing the Pentium II Processor Memory Configurations Memory Upgrade17 Installing a Dimm Installing a Dimm18 Removing a Dimm Removing a DimmReconfiguring the System Installing PCI Cards Installing Expansion CardsBios detects and configures only PnP cards Installing ISA Cards20 Installing an ISA Card Installing an AGP Card21 Installing an AGP Card Error Messages Software Error MessagesSystem Error Messages System Board Mmmmssssooo Wxxxx Correcting Error Conditions Page Setup Utility Setup Utility Entering SetupSetup Utility System Information Processor Processor SpeedInternal Cache Size Floppy Drive a External CacheFloppy Drive B IDE Primary Channel MasterTotal Memory IDE Secondary Channel SlaveSerial Port Parallel Port15 PS/2 Mouse Product Name Product InformationSystem S/N Main Board IDSystem Bios Version DMI Bios VersionMain Board S/N Floppy Drives Disk Drives2 LS-120 Drive Compatible As IDE DrivesIDE Primary Channel Master IDE Primary Channel Slave IDE Secondary Channel MasterIDE Secondary Channel Slave This parameter specifies the size of your hard disk, in MB Enhanced IDE Features DisabledDMA Transfer Mode Onboard Peripherals Serial Ports 1Base Address ∙ 3BCh ∙ 378h ∙ 278h Operation Mode Onboard Device SettingsIDE Controller Floppy Disk ControllerPS/2 Mouse Controller USB Host ControllerOnboard Ethernet Chip SMBus Interrupt IRQ9Power Management Power Management ModeIDE Hard Disk Standby Timer System Sleep Timer Power Switch 4 secModem Ring Indicator System Wake-up EventBoot Sequence Boot OptionsFast Boot Silent BootFirst Hard Disk Drive Configuration Table Num Lock After BootBoot from LANDesk Service Agent Memory TestDate Date and TimeTime Memory/Cache Options Advanced OptionsInternal Cache CPU Cache External CacheMemory at 15MB-16MB Reserved for Memory Parity Mode 2 PnP/PCI OptionsFor system board with LAN For system board without LAN PCI IRQ SettingVGA Palette Snoop PCI IRQ SharingCPU Frequency Reset Resource AssignmentsGraphics Aperture Size Plug and Play OSBus Frequency CPU MultipleProcessor Speed Setup Password To set or change a PasswordSystem Security Setup Utility To remove your Setup Password To bypass Setup Password Make sure to set JP3 to 1-2 to enable Power-on password Power-on PasswordDisk Drive Control Drive Control SettingsAbort Settings Change Load Default SettingsExit Setup