Acer M11E manual Installing a Dimm

Page 37

Table 1-3

Memory Configurations

 

 

 

 

 

 

 

Bank 0

Bank 1

Bank 2

Total Memory

 

128 MB

 

 

128 MB

 

 

 

 

 

 

128 MB

128 MB

 

256 MB

 

 

 

 

 

 

128 MB

128 MB

128 MB

384 MB

 

 

 

 

 

1.6.2Installing a DIMM

To install a DIMM, align it with the socket and press it down until the holding clips secure the DIMM in place.

The DIMM socket is slotted to ensure proper installation. If you slip in a DIMM but it does not completely fit, you may have inserted it the wrong way. Reverse the orientation of the DIMM.

Figure 1-17 Installing a DIMM

System Board

1-21

Image 37
Contents M11E System Copyright Important Safety Instructions Page Page CD ROM Safety Warning Vii FCC Class B Radio Frequency Interference Statement Manual Structure About this Manual PurposeConventions Table of Contents Xii Bios UtilityXiii Xiv List of FiguresList of Tables Page System Board FeaturesUser’s Guide Major Components System Board Layout System Board Layout with Network ConnectorSystem Board Layout without Network Connector Jumper and Connector Locations Jumpers and ConnectorsBlackened pin of a jumper or connector represents pin Connector Functions Jumper SettingsJP1 ESD Precautions Attaching the Processor Fan Sink Installing the Pentium II processorRemoving tape protector from Fan SInk Locking a Wide Clip End 10 Locking the metal bracket 11 Installing the Pentium II Retention Mechanism Installing a Pentium II Processor12 Installing the Pentium II Retention Mechanism 13 Installing a Pentium II Processor 14 Securing the Pentium II Processor Removing a Pentium II Processor16 Removing the Pentium II Processor Memory Configurations Memory Upgrade17 Installing a Dimm Installing a Dimm18 Removing a Dimm Removing a DimmReconfiguring the System Installing PCI Cards Installing Expansion CardsBios detects and configures only PnP cards Installing ISA Cards20 Installing an ISA Card Installing an AGP Card21 Installing an AGP Card Software Error Messages Error MessagesSystem Error Messages System Board Mmmmssssooo Wxxxx Correcting Error Conditions Page Setup Utility Setup Utility Entering SetupSetup Utility System Information Processor Speed ProcessorInternal Cache Size Floppy Drive a External CacheFloppy Drive B IDE Primary Channel MasterTotal Memory IDE Secondary Channel SlaveSerial Port Parallel Port15 PS/2 Mouse Product Name Product InformationSystem S/N Main Board IDDMI Bios Version System Bios VersionMain Board S/N Floppy Drives Disk DrivesIDE Drives 2 LS-120 Drive Compatible AsIDE Primary Channel Master IDE Secondary Channel Master IDE Primary Channel SlaveIDE Secondary Channel Slave This parameter specifies the size of your hard disk, in MB Enhanced IDE Features DisabledDMA Transfer Mode Serial Ports 1 Onboard PeripheralsBase Address ∙ 3BCh ∙ 378h ∙ 278h Operation Mode Onboard Device SettingsIDE Controller Floppy Disk ControllerPS/2 Mouse Controller USB Host ControllerOnboard Ethernet Chip SMBus Interrupt IRQ9Power Management Mode Power ManagementIDE Hard Disk Standby Timer System Sleep Timer Power Switch 4 secModem Ring Indicator System Wake-up EventBoot Sequence Boot OptionsSilent Boot Fast BootFirst Hard Disk Drive Configuration Table Num Lock After BootBoot from LANDesk Service Agent Memory TestDate Date and TimeTime Memory/Cache Options Advanced OptionsExternal Cache Internal Cache CPU CacheMemory at 15MB-16MB Reserved for 2 PnP/PCI Options Memory Parity ModeFor system board with LAN For system board without LAN PCI IRQ SettingVGA Palette Snoop PCI IRQ SharingCPU Frequency Reset Resource AssignmentsGraphics Aperture Size Plug and Play OSCPU Multiple Bus FrequencyProcessor Speed To set or change a Password Setup PasswordSystem Security Setup Utility To remove your Setup Password To bypass Setup Password Make sure to set JP3 to 1-2 to enable Power-on password Power-on PasswordDisk Drive Control Drive Control SettingsAbort Settings Change Load Default SettingsExit Setup