Siemens SPC3 manual Description of the DP Services, SetSlaveAddress SAP55

Page 31

 

 

SPC3

PROFIBUS Interface Center

 

 

 

 

 

 

6.2 Description of the DP Services

6.2.1 Set_Slave_Address (SAP55)

6.2.1.1 Sequence for the Set_Slave_Address Utility

The user can disable this utility by setting the ‘R_SSA_Puf_Ptr = 00H’ buffer pointer. The slave address must then be determined, for example, by reading a switch, and written in the R_TS_Adr. RAM register.

The user must make a retentive memory possibility available (for example, EEPROM) to support this utility. It must be possible to store the ‘station address’and the ‘Real_No_Add_Change’ (‘True’ = FFH) paramet r in this external EEPROM. After each restart caused by a power failure, the user must again make these values available to SPC3 in the R_TS_Adr und R_Real_No_Add_Change RAM register.

If SAP55 is enabled and the Set_Slave_Address telegram is correctly accepted, SPC3 enters all net data in the Aux-Puffer1/2, exchanges the Aux buffer1/2 for the SSA buffer, stores the entered data length in ‘R_Len_SSA_Data’, generates the ‘New_SSA_Data’ interrupt and internally stores the new ‘station address’ and the new ‘Real_No_Add_Change’ parameter. The user does not need to transfer this changed

parameter to SPC3 again. After the user has read the buffer, the user generates the ‘SSA_Puffer_Free_Cmd’ (read operation on address 14H). This makes SPC3 again ready to receive an additional Set Slave Address telegram (such as from another master).

SPC3 reacts independently when there are errors.

Address

 

 

 

Bit Position

 

 

 

Designation

Control

7

6

5

4

3

2

1

0

 

Register

 

 

 

 

 

 

 

 

 

14H

0

0

0

0

0

0

0

0

SSA_Puffer_Free_Cmd

 

 

 

 

don´t care

 

 

 

 

Figure 6.3: Coding SSA_Buffer_Free_Cmd

 

 

 

6.2.1.2 Structure of the Set_Slave_Address Telegram The net data are stored as follows in the SSA buffer:

Byte

 

 

 

Bit Position

 

 

 

Designation

 

7

6

5

4

3

2

1

0

 

0

 

 

 

 

 

 

 

 

New_Slave_Address

1

 

 

 

 

 

 

 

 

Ident_Number_High

2

 

 

 

 

 

 

 

 

Ident_Number_Low

3

 

 

 

 

 

 

 

 

No_Add_Chg

4-243

 

 

 

 

 

 

 

 

Rem_Slave_Data additional application-

 

 

 

 

 

 

 

 

 

specific data

Figure 6.4: Data Format for the Set_Slave_Address Telegram

SPC3 Hardware Description

V1.3

Page 29

Copyright (C) Siemens AG 2003 All rights reserved.

 

2003/04

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Simatic NET Page SIM Atic NET SPC3 Hardware Description Profibus Interface CenterRelease Date Changes VersionsDirectory Mode RegisterStatus Register Interrupt Controller Watchdog Timer DPBuffer Structure Description of the DP ServicesAsic Test 11.3 Diagnostics Processing from the System ViewPin Assignment Example for the RS 485 Interface SPC3 Introduction Function Overview Cmos Pin DescriptionCPD Cmos with pull down TTLt Schmitt trigger V1.3 Memory Area Distribution in the SPC3 Memory Allocation5FFH Segment Processor Parameters Latches/Register OCH 0DH Significance Write Access0EH 0FH Organizational Parameters RAM 1DH 1AH1BH 1CHAsic Interface Mode RegisterDisstartcontrol EOI Mode Register 1 Mode-REG1, writableSTARTSPC3 Exiting the Offline stateStatus Register Status Register Bit15 . .readable FdlindstSPC3 IRR IMR Interrupt ControllerDxout IAR IMRResponse Time Monitoring Watchdog TimerAutomatic Baud Rate Identification Baud Rate MonitoringDPBuffer Structure PROFIBUS-DP InterfaceUart Aux-Buffer Management RAMSetSlaveAddress SAP55 Description of the DP ServicesSequence for the SetSlaveAddress Utility Parameter Data Structure SetParam SAP61Parameter Data Processing Sequence SPC3 CheckConfig SAP62SlaveDiagnosis SAP60 Diagnostics Processing SequenceSPC3 WriteReadData / DataExchange DefaultSAP Structure of the Diagnostics BufferWriting Outputs Reading Inputs GlobalControl SAP58 UserWatchdogTimerReadInputs SAP56 GetConfig SAP59ReadOutputs SAP57 Bus Interface Unit BIU Hardware InterfaceUniversal Processor Bus Interface General DescriptionBus Interface V1.3 XINT/MO ModeLow Cost System with 80C32 Switching Diagram PrinciplesSystem X86-Mode Application with the 80 C SPC3Application with th 80 C Uart Interface SignalsAsic Test DC-Specifikation of the I/O- Drivers Technical DataMaximum Limit Values Permitted Operating ValuesTabel 8.3 DC-Specifikation of the I/O- Drivers AC-Specification for the Output DriversCurrent Tabelle 8.5 Leakage current of the output drivers Clock Pulse Timing Timing CharacteristicsSYS Bus Interface Clock pulse 48 MhzTBD ResetTiming in the Synchronous C32-Mode ST-Vers Min Max UnitSynchronous Intel-Mode, Processor-Write-Timing Synchronous Intel-Mode, Processor-Read-TimingST-Vers Timing in the Asynchronous Intel Mode X86 ModeParameter Min Max XWR XCS Asynchronous Intel-Mode, Processor-Read-TimingXRD XCS Xready Asynchronous Intel-Mode, Processor-Write-TimingSynchronous Motorola-Mode, Processor-Read-Timing 4.1 74.2Timing in the Asynchronous Motorola-Mode for example, 68HC16 Synchronous Motorola-Mode, Processor-Write-TimingXCS Xdsack Asynchronous Motorola-Mode, Processor-Read-TimingAsynchronous Motorola-Mode, Processor-Write-Timing Pulse 48 MHz Serial Bus InterfaceHousing PQFP-44 Housing SPC3 Hardware Description 14.15 Symbol Min Typ Max AMI-Vers13.65 13.90TXD Profibus InterfacePin Assignment RTSSN65ALS1176 Example for the RS 485 InterfaceTechnical contact person at ComDeC in Germany AppendixAddresses Profibus User Organisation10.3.2 SPC3 ST General Definition of TermsOrdering of ASICs 10.3.1 SPC3 AMIStatdiag Appendix a Diagnostics Processing in Profibus DPDiagnostics Bits and Expanded Diagnostics IntroductionIdentifier Byte 7 has Etc Identifier Byte 0 has Combi Diagnostics Processing from the System ViewSingle Diagnostics Simatic S5 / COM ETData format in the Siemens PLC Simatic Appendix B Useful InformationPage Siemens Aktiengesellschaft

SPC3 specifications

Siemens SPC3 is a state-of-the-art solution designed to enhance industrial automation, providing businesses with a robust platform for managing complex processes efficiently. This device epitomizes Siemens' commitment to innovation, blending cutting-edge technology with user-friendly features to deliver optimized performance across various applications.

One of the standout features of the Siemens SPC3 is its advanced processing capabilities. Equipped with high-performance processors, it can handle various tasks simultaneously, ensuring seamless operation even in demanding environments. This performance is complemented by enhanced memory capacity, which allows for increased data handling and improved execution speed, crucial for real-time monitoring and control applications.

The Siemens SPC3 also integrates a modular design, enabling flexibility and scalability. This characteristic allows users to customize their systems according to specific operational needs, adding or removing components as required. This adaptability is particularly beneficial for businesses that aim to scale their operations without incurring the substantial costs associated with overhauling existing systems.

Furthermore, the SPC3 employs the latest communication technologies, ensuring interoperability with various devices and systems. It supports industry-standard protocols, facilitating efficient data exchange between components. This connectivity is vital for establishing smart factories and enhancing overall productivity by creating a unified ecosystem.

Another significant aspect of the Siemens SPC3 is its focus on security. As cyber threats in industrial settings become increasingly sophisticated, Siemens prioritizes safeguarding user data and system integrity. The SPC3 incorporates advanced security features, including encryption and access control measures, to protect against unauthorized access and ensure data confidentiality.

Siemens has also emphasized ease of use in the SPC3. The interface is designed to be intuitive, allowing operators to navigate and configure the system effortlessly. Coupled with comprehensive software tools, users are empowered to implement changes swiftly while minimizing downtime.

In terms of energy efficiency, the SPC3 incorporates technologies that allow for optimized energy consumption, aligning with sustainability goals prevalent in today’s industries. By reducing energy waste, businesses not only lower operational costs but also contribute to environmental conservation.

In summary, Siemens SPC3 represents a significant advancement in industrial automation technology. Its high-performance processing, modular adaptability, advanced communication capabilities, robust security measures, and user-friendly design make it an ideal choice for businesses striving for efficiency and innovation in their operations. The SPC3 is more than just a control device; it is a comprehensive solution that meets the evolving demands of modern industries.
Top Page Image Contents