Siemens manual Housing PQFP-44 Housing SPC3 Hardware Description

Simatic NET Page SIM Atic NET SPC3 Hardware Description Profibus Interface CenterRelease Date Changes VersionsStatus Register Interrupt Controller Watchdog Timer Mode RegisterDPBuffer Structure Description of the DP Services Directory11.3 Diagnostics Processing from the System View Asic TestPin Assignment Example for the RS 485 Interface SPC3 Introduction Function Overview Cmos Pin DescriptionCPD Cmos with pull down TTLt Schmitt trigger V1.3 Memory Allocation Memory Area Distribution in the SPC35FFH Segment Processor Parameters Latches/Register Significance Write Access OCH 0DH0EH 0FH Organizational Parameters RAM 1BH 1AH1CH 1DHAsic Interface Mode RegisterDisstartcontrol STARTSPC3 Mode Register 1 Mode-REG1, writableExiting the Offline state EOIStatus Register Status Register Bit15 . .readable FdlindstSPC3 IRR IMR Interrupt ControllerDxout IAR IMRAutomatic Baud Rate Identification Watchdog TimerBaud Rate Monitoring Response Time MonitoringDPBuffer Structure PROFIBUS-DP InterfaceUart Aux-Buffer Management RAMDescription of the DP Services SetSlaveAddress SAP55Sequence for the SetSlaveAddress Utility SetParam SAP61 Parameter Data StructureParameter Data Processing Sequence SPC3 CheckConfig SAP62Diagnostics Processing Sequence SlaveDiagnosis SAP60SPC3 Structure of the Diagnostics Buffer WriteReadData / DataExchange DefaultSAPWriting Outputs Reading Inputs GlobalControl SAP58 UserWatchdogTimerGetConfig SAP59 ReadInputs SAP56ReadOutputs SAP57 Universal Processor Bus Interface Hardware InterfaceGeneral Description Bus Interface Unit BIUBus Interface V1.3 XINT/MO ModeLow Cost System with 80C32 Switching Diagram PrinciplesSystem X86-Mode Application with the 80 C SPC3Application with th 80 C Interface Signals UartAsic Test Maximum Limit Values Technical DataPermitted Operating Values DC-Specifikation of the I/O- DriversAC-Specification for the Output Drivers Tabel 8.3 DC-Specifikation of the I/O- DriversCurrent Tabelle 8.5 Leakage current of the output drivers SYS Bus Interface Timing CharacteristicsClock pulse 48 Mhz Clock Pulse TimingTiming in the Synchronous C32-Mode ResetST-Vers Min Max Unit TBDSynchronous Intel-Mode, Processor-Write-Timing Synchronous Intel-Mode, Processor-Read-TimingTiming in the Asynchronous Intel Mode X86 Mode ST-VersParameter Min Max XRD XCS Xready Asynchronous Intel-Mode, Processor-Read-TimingAsynchronous Intel-Mode, Processor-Write-Timing XWR XCS Synchronous Motorola-Mode, Processor-Read-Timing 4.1 74.2Timing in the Asynchronous Motorola-Mode for example, 68HC16 Synchronous Motorola-Mode, Processor-Write-TimingAsynchronous Motorola-Mode, Processor-Read-Timing XCS XdsackAsynchronous Motorola-Mode, Processor-Write-Timing Pulse 48 MHz Serial Bus InterfaceHousing PQFP-44 Housing SPC3 Hardware Description 13.65 Symbol Min Typ Max AMI-Vers13.90 14.15Pin Assignment Profibus InterfaceRTS TXDSN65ALS1176 Example for the RS 485 InterfaceAddresses AppendixProfibus User Organisation Technical contact person at ComDeC in GermanyOrdering of ASICs General Definition of Terms10.3.1 SPC3 AMI 10.3.2 SPC3 STDiagnostics Bits and Expanded Diagnostics Appendix a Diagnostics Processing in Profibus DPIntroduction StatdiagIdentifier Byte 7 has Etc Identifier Byte 0 has Single Diagnostics Diagnostics Processing from the System ViewSimatic S5 / COM ET CombiData format in the Siemens PLC Simatic Appendix B Useful InformationPage Siemens Aktiengesellschaft