BenQ SP890 user manual Connecting component-video devices, Connecting S-Video or video devices

Page 18

English

Connecting component-video devices

Be sure to match the corresponding colors between the cables and the terminals. The RCA type component video jacks are provided for connection to video output devices. The audio connections are provided for informational purposes only. You can also connect the separate audio cable to a suitable audio amplifier.

AV equipment: DVD player,

digital tuner, etc.

Audio cable

Component video cable

Speakers

Audio cable

Connecting S-Video or video devices

You need only connect S-Video or composite Video cable from the same device, never both at the same time. The audio connections are provided for informational purposes only. You can also connect the separate audio cable to a suitable audio amplifier.

AV equipment

Audio cable

S-Video cable or

Video cable

Speakers

Audio cable

• If you have already made a Component Video connection between the projector and the video source device, you need not connect to this device again using an S-Video or composite Video connection as this makes an unnecessary second connection of poorer picture quality. You need only connect using a composite Video connection if both Component Video and S-Video are not supplied on the video source device (for example, with some analog video cameras).

•If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, please check that the video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

18 Connecting with video equipment

Image 18

Contents Welcome Table of contents Important safety instructions Do not cover the projector with any item Moisture condensation Avoid volatile liquidsDisposal Shipping contents OverviewRemote control batteries Remote control operationCeiling mounting the projector Projector features Rear view Projector exterior viewFront and upper side view Under viewControl panel Remote control Ceiling Front Choosing a locationFloor Front Floor RearObtaining a preferred projected image size Projection dimensions Installation for a 169 ratio screenLens Installation for a 43 ratio screenHighest Height HShifting the projection lens To use the lens shift leverReference Picture quality Connecting Hdmi devicesPreparations ComponentConnecting component-video devices Connecting S-Video or video devicesConnecting a computer Connecting a monitorConnect the projector to a computer with a VGA cable Turning the projector on PreparationsUsing the OSD menu Selecting an input sourceChanging Color Space Use / to highlight the System Setup menu Using the menusUsing a security cable lock Securing the projectorUtilizing the password function Setting a passwordIf you forget the password Entering the password recall procedure Changing the passwordDisabling the password function Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityCorrecting picture distortion Two parallel sidesNo parallel sides Fine-tuning the selected picture mode Using the preset and user modesSelecting a preset mode To fine-tune the picture modePress to highlight Load Settings From Setting the User 1/User 2 modeResetting the picture mode To reset the picture mode to the preset factory valuesFine-tuning the picture quality Advanced picture quality controls Setting Black LevelSelecting a color temperature Controlling image clarityAdjusting Brilliant Color Setting a preferred color temperatureSelecting a Gamma setting To set a preferred color temperatureSetting Film Mode To adjust and store the settingsColor Management Setting 3D Comb Filter Selecting the aspect ratioAbout the aspect ratio Aspect ratio Aspect ratio image Using Panamorph lenses optionalImage Using the entire resolution 169 displayHiding the image Utilizing FAQ functionDisable Freezing the imageTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Muting the soundControlling the projector remotely through a web browser Configuring the Lan Control SettingsControlling the projector through a Lan environment If you are in a Dhcp environmentMenu item Ii To switch input source, click on your desired signalAuto Source Press Exit to go back to the remote network operationTo activate High Altitude Mode Press to highlight High Altitude ModeOperating in a high altitude environment Highlight PIP and press / to select On Displaying more than one image source simultaneouslyTo display the PIP window PIP function is effective at below source combinationsTurning the projector off On-Screen Display OSD menus On-Screen Display OSD structureMain menu Sub-menu Options System Setup DisplaySetup InformationPicture -- Basic menu Picture -- Advanced menuFunction Description Display menu Closed Caption Enable Sleep TimerMenu Settings Menu Position LanguageAdvanced Setup menu Information menu Care of the projector Cleaning the lensCleaning the projector case Storing the projectorLamp information Setting Lamp Power as EconomicSetting Auto Off Getting to know the lamp hourTiming of replacing the lamp Replacing the lampStatus Message Reapply power and turn the projector back on Resetting the lamp timer Indicators Power Temp Lamp Status & DescriptionTroubleshooting Problem Cause RemedyElectrical SpecificationsOptical TerminalsDimensions Mm x 318 mm x 169 mm W x D x HSupported timing for PC input Timing chartFormat Resolution Refresh rate Frequency KHz MHzSupported timing for Edtv and Hdtv via Component inputs Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Video and S-Video inputsWarranty CopyrightDisclaimer MIC statement FCC statement for United States usersEEC statement for European users Weee directiveEnglish