BenQ SP890 user manual Selecting an input source, Using the OSD menu, Changing Color Space

Page 21

Selecting an input source

The projector can be connected to multiple equipment at the same time. When the projector is first turned on, it will attempt to reconnect with the input source which was in use when the projector was last shut down.

To select the video source:

•Using the remote control or projector

Press one of the Source keys on the remote control, or press SOURCE on the projector repeatedly until your desired signal is selected.

•Using the OSD menu

1.Press MENU on the projector or MENU/EXIT on the remote control, and then press / until the System Setup menu is highlighted.

2.Press to highlight Input Source and press ENTER. The source selection bar is displayed.

3.Press / repeatedly until your desired signal is selected and press

ENTER.

Once detected, the selected source information will be displayed on the screen for seconds. If there are multiple pieces of equipment connected to the projector, you can go back to the source selection bar again to search for other signals.

•If you want the projector to automatically search for the signals, select On in the System Setup > Auto Source Search menu.

•If you want to use the PIP function, see "Displaying more than one image source simultaneously" on page 40 for details.

System Setup

Language	English
Splash Screen	BenQ
Projector Position	Floor Front
Auto Off	Disable
Sleep Timer	Disable
Background Color	Blue
Menu Settings
Input Source	ENTER
Auto Source Search	On
Closed Caption
Standby Monitor Out	Off
S-Video	EXIT Back

	HDMI	NOTE: When
		automatically
	Video	searching for a valid
	S-Video	input source, the
		projector cycles
	Component 1	through the
	Component 2	available signals
	Component 2	following the
		following the
	PC	sequence from top
		to bottom as the
		source selection bar
		shows.

English

Changing Color Space

In the unlikely event that you connect the projector to a DVD player via the projector's HDMI input and the projected picture displays wrong colors, please change the color space to YUV.

1.Press MENU/EXIT and then press / until the Display menu is highlighted.

2.Press to highlight Color Space Conversion and press / to select a suitable color space.

This function is only available when the HDMI input port is in use.

Using the projector

21

Image 21

Contents Welcome Table of contents Important safety instructions Do not cover the projector with any item Moisture condensation Avoid volatile liquidsDisposal Overview Shipping contentsRemote control batteries Remote control operationCeiling mounting the projector Projector features Front and upper side view Projector exterior viewRear view Under viewControl panel Remote control Floor Front Choosing a locationCeiling Front Floor RearObtaining a preferred projected image size Installation for a 169 ratio screen Projection dimensionsHighest Installation for a 43 ratio screenLens Height HTo use the lens shift lever Shifting the projection lensPreparations Connecting Hdmi devicesReference Picture quality ComponentConnecting S-Video or video devices Connecting component-video devicesConnecting a computer Connecting a monitorConnect the projector to a computer with a VGA cable Preparations Turning the projector onUsing the OSD menu Selecting an input sourceChanging Color Space Using a security cable lock Using the menusUse / to highlight the System Setup menu Securing the projectorUtilizing the password function Setting a passwordIf you forget the password Entering the password recall procedure Changing the passwordDisabling the password function Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting picture distortion Two parallel sidesNo parallel sides Selecting a preset mode Using the preset and user modesFine-tuning the selected picture mode To fine-tune the picture modeResetting the picture mode Setting the User 1/User 2 modePress to highlight Load Settings From To reset the picture mode to the preset factory valuesFine-tuning the picture quality Selecting a color temperature Setting Black LevelAdvanced picture quality controls Controlling image claritySelecting a Gamma setting Setting a preferred color temperatureAdjusting Brilliant Color To set a preferred color temperatureSetting Film Mode To adjust and store the settingsColor Management Setting 3D Comb Filter Selecting the aspect ratioAbout the aspect ratio Image Using the entire resolution Using Panamorph lenses optionalAspect ratio Aspect ratio image 169 displayDisable Utilizing FAQ functionHiding the image Freezing the imageAdjusting the sound level Adjusting the soundTurning off the Power On/Off Ring Tone Muting the soundControlling the projector through a Lan environment Configuring the Lan Control SettingsControlling the projector remotely through a web browser If you are in a Dhcp environmentAuto Source Ii To switch input source, click on your desired signalMenu item Press Exit to go back to the remote network operationTo activate High Altitude Mode Press to highlight High Altitude ModeOperating in a high altitude environment To display the PIP window Displaying more than one image source simultaneouslyHighlight PIP and press / to select On PIP function is effective at below source combinationsTurning the projector off On-Screen Display OSD menus On-Screen Display OSD structureMain menu Sub-menu Options Display System SetupInformation SetupPicture -- Basic menu Picture -- Advanced menuFunction Description Display menu Menu Settings Menu Position Sleep TimerClosed Caption Enable LanguageAdvanced Setup menu Information menu Cleaning the projector case Cleaning the lensCare of the projector Storing the projectorSetting Auto Off Setting Lamp Power as EconomicLamp information Getting to know the lamp hourTiming of replacing the lamp Replacing the lampStatus Message Reapply power and turn the projector back on Resetting the lamp timer Power Temp Lamp Status & Description IndicatorsProblem Cause Remedy TroubleshootingOptical SpecificationsElectrical TerminalsMm x 318 mm x 169 mm W x D x H DimensionsFormat Resolution Refresh rate Frequency Timing chartSupported timing for PC input KHz MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzSupported timing for Edtv and Hdtv via Component inputs Supported timing for Video and S-Video inputsWarranty CopyrightDisclaimer EEC statement for European users FCC statement for United States usersMIC statement Weee directiveEnglish