BenQ SP890 user manual Do not cover the projector with any item

Page 4

English

5.Do not block the vents holes while the projector is on (even in standby mode):

-Do not cover the projector with any item;

-Do not place the projector on a blanket, bedding or any other soft surface.

6.In areas where the mains power supply voltage may fluctuate by ±10 volts, it is recommended that you connect your projector through a power stabilizer, surge protector or uninterruptible power supply (UPS) as appropriate to your situation.

7.Do not step on the projector or place any objects upon it.

8.Do not place liquids near or on the projector. Liquids spilled into the projector will void your warranty. If the projector does become wet, disconnect it from the power point and call BenQ to have the projector repaired.

9.Do not look straight into the projector lens during operation. It may harm your sight.

10.Do not operate the projector lamp beyond the rated lamp life. Excessive operation of lamps beyond the rated life could cause a lamp to break on rare occasions.

11.The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement.

12.This projector is capable of displaying inverted images for ceiling mount installation. Use only BenQ's Ceiling Mount Kit for mounting.

4	Important safety instructions

Image 4

Contents Welcome Table of contents Important safety instructions Do not cover the projector with any item Avoid volatile liquids Moisture condensationDisposal Shipping contents OverviewRemote control operation Remote control batteriesCeiling mounting the projector Projector features Projector exterior view Front and upper side viewRear view Under viewControl panel Remote control Choosing a location Floor FrontCeiling Front Floor RearObtaining a preferred projected image size Projection dimensions Installation for a 169 ratio screenInstallation for a 43 ratio screen HighestLens Height HShifting the projection lens To use the lens shift leverConnecting Hdmi devices PreparationsReference Picture quality ComponentConnecting component-video devices Connecting S-Video or video devicesConnecting a monitor Connecting a computerConnect the projector to a computer with a VGA cable Turning the projector on PreparationsSelecting an input source Using the OSD menuChanging Color Space Using the menus Using a security cable lockUse / to highlight the System Setup menu Securing the projectorSetting a password Utilizing the password functionIf you forget the password Changing the password Entering the password recall procedureDisabling the password function Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityTwo parallel sides Correcting picture distortionNo parallel sides Using the preset and user modes Selecting a preset modeFine-tuning the selected picture mode To fine-tune the picture modeSetting the User 1/User 2 mode Resetting the picture modePress to highlight Load Settings From To reset the picture mode to the preset factory valuesFine-tuning the picture quality Setting Black Level Selecting a color temperatureAdvanced picture quality controls Controlling image claritySetting a preferred color temperature Selecting a Gamma settingAdjusting Brilliant Color To set a preferred color temperatureTo adjust and store the settings Setting Film ModeColor Management Selecting the aspect ratio Setting 3D Comb FilterAbout the aspect ratio Using Panamorph lenses optional Image Using the entire resolutionAspect ratio Aspect ratio image 169 displayUtilizing FAQ function DisableHiding the image Freezing the imageAdjusting the sound Adjusting the sound levelTurning off the Power On/Off Ring Tone Muting the soundConfiguring the Lan Control Settings Controlling the projector through a Lan environmentControlling the projector remotely through a web browser If you are in a Dhcp environmentIi To switch input source, click on your desired signal Auto SourceMenu item Press Exit to go back to the remote network operationPress to highlight High Altitude Mode To activate High Altitude ModeOperating in a high altitude environment Displaying more than one image source simultaneously To display the PIP windowHighlight PIP and press / to select On PIP function is effective at below source combinationsTurning the projector off On-Screen Display OSD structure On-Screen Display OSD menusMain menu Sub-menu Options System Setup DisplaySetup InformationPicture -- Advanced menu Picture -- Basic menuFunction Description Display menu Sleep Timer Menu Settings Menu PositionClosed Caption Enable LanguageAdvanced Setup menu Information menu Cleaning the lens Cleaning the projector caseCare of the projector Storing the projectorSetting Lamp Power as Economic Setting Auto OffLamp information Getting to know the lamp hourReplacing the lamp Timing of replacing the lampStatus Message Reapply power and turn the projector back on Resetting the lamp timer Indicators Power Temp Lamp Status & DescriptionTroubleshooting Problem Cause RemedySpecifications OpticalElectrical TerminalsDimensions Mm x 318 mm x 169 mm W x D x HTiming chart Format Resolution Refresh rate FrequencySupported timing for PC input KHz MHzFormat Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHz Format Resolution Refresh rate Freq. KHz Pixel Freq MHzSupported timing for Edtv and Hdtv via Component inputs Supported timing for Video and S-Video inputsCopyright WarrantyDisclaimer FCC statement for United States users EEC statement for European usersMIC statement Weee directiveEnglish