BenQ SP890 user manual Adjusting the sound, Muting the sound, To temporarily turn off the sound

Page 36

English

Adjusting the sound

The sound adjustments made as below will have an effect on the projector speaker(s). Be sure you have made a correct connection to the projector audio input. See "Connecting with video equipment" on page 17 for how the audio input is connected.

Muting the sound

To temporarily turn off the sound:

1.Press MENU on the projector or MENU/EXIT on the remote control to open the OSD menu and press

/ to highlight the Advanced Setup menu.

2.Press to highlight Audio Settings and press ENTER. The Audio Settings page is displayed.

3.Highlight Mute and press / to select On.

Adjusting the sound level

To adjust the sound level, press VOLUME+/VOLUME- on the remote control, or:

1.Repeat steps 1-2above.

2.Press to highlight Volume and press / to select a desired sound level.

Turning off the Power On/Off Ring Tone

To turn off the ring tone:

1.Repeat steps 1-2above.

2.Press to highlight Power On/Off Ring Tone and press / to select Off.

The only way to change Power On/Off Ring Tone is setting On or Off here. Setting the sound mute or changing the sound level will not affect the Power On/Off Ring Tone.

36 Using the projector

Image 36

Contents Welcome Table of contents Important safety instructions Do not cover the projector with any item Moisture condensation Avoid volatile liquidsDisposal Shipping contents OverviewRemote control batteries Remote control operationCeiling mounting the projector Projector features Projector exterior view Front and upper side viewRear view Under viewControl panel Remote control Choosing a location Floor FrontCeiling Front Floor RearObtaining a preferred projected image size Projection dimensions Installation for a 169 ratio screenInstallation for a 43 ratio screen HighestLens Height HShifting the projection lens To use the lens shift leverConnecting Hdmi devices PreparationsReference Picture quality ComponentConnecting component-video devices Connecting S-Video or video devicesConnecting a computer Connecting a monitorConnect the projector to a computer with a VGA cable Turning the projector on PreparationsUsing the OSD menu Selecting an input sourceChanging Color Space Using the menus Using a security cable lockUse / to highlight the System Setup menu Securing the projectorUtilizing the password function Setting a passwordIf you forget the password Entering the password recall procedure Changing the passwordDisabling the password function Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting picture distortion Two parallel sidesNo parallel sides Using the preset and user modes Selecting a preset modeFine-tuning the selected picture mode To fine-tune the picture modeSetting the User 1/User 2 mode Resetting the picture modePress to highlight Load Settings From To reset the picture mode to the preset factory valuesFine-tuning the picture quality Setting Black Level Selecting a color temperatureAdvanced picture quality controls Controlling image claritySetting a preferred color temperature Selecting a Gamma settingAdjusting Brilliant Color To set a preferred color temperatureSetting Film Mode To adjust and store the settingsColor Management Setting 3D Comb Filter Selecting the aspect ratioAbout the aspect ratio Using Panamorph lenses optional Image Using the entire resolutionAspect ratio Aspect ratio image 169 displayUtilizing FAQ function DisableHiding the image Freezing the imageAdjusting the sound Adjusting the sound levelTurning off the Power On/Off Ring Tone Muting the soundConfiguring the Lan Control Settings Controlling the projector through a Lan environmentControlling the projector remotely through a web browser If you are in a Dhcp environmentIi To switch input source, click on your desired signal Auto SourceMenu item Press Exit to go back to the remote network operationTo activate High Altitude Mode Press to highlight High Altitude ModeOperating in a high altitude environment Displaying more than one image source simultaneously To display the PIP windowHighlight PIP and press / to select On PIP function is effective at below source combinationsTurning the projector off On-Screen Display OSD menus On-Screen Display OSD structureMain menu Sub-menu Options System Setup DisplaySetup InformationPicture -- Basic menu Picture -- Advanced menuFunction Description Display menu Sleep Timer Menu Settings Menu PositionClosed Caption Enable LanguageAdvanced Setup menu Information menu Cleaning the lens Cleaning the projector caseCare of the projector Storing the projectorSetting Lamp Power as Economic Setting Auto OffLamp information Getting to know the lamp hourTiming of replacing the lamp Replacing the lampStatus Message Reapply power and turn the projector back on Resetting the lamp timer Indicators Power Temp Lamp Status & DescriptionTroubleshooting Problem Cause RemedySpecifications OpticalElectrical TerminalsDimensions Mm x 318 mm x 169 mm W x D x HTiming chart Format Resolution Refresh rate FrequencySupported timing for PC input KHz MHzFormat Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHz Format Resolution Refresh rate Freq. KHz Pixel Freq MHzSupported timing for Edtv and Hdtv via Component inputs Supported timing for Video and S-Video inputsWarranty CopyrightDisclaimer FCC statement for United States users EEC statement for European usersMIC statement Weee directiveEnglish