BenQ SP890 user manual Adjusting the projected image, Adjusting the projection angle

Page 25

Adjusting the projected image

Adjusting the projection angle

There are four adjuster feet on the bottom of the projector. These can be used if necessary to change the projection angle. Screw the feet in or out as appropriate to aim and level the projection angle.

If the screen and the projector are not perpendicular to each other, the projected image becomes vertical trapezoidal. To correct this problem, see "Correcting picture distortion" on page 26 for details.

Auto-adjusting the image

In some cases, you may need to optimize the picture quality. To do this, press AUTO on the projector or remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of

Frequency and Clock to provide the best picture quality.

The current source information will be displayed in the corner of the screen for 3 seconds.

• The screen will be blank while AUTO is functioning.

•This function is only available when a PC signal (analog RGB) is selected.

Fine-tuning the image size and clarity

1. Adjust the projected picture to the size that

2. Sharpen the picture by rotating the focus

you need using the zoom ring.

ring.

English

Using the projector

25

Image 25

Contents Welcome Table of contents Important safety instructions Do not cover the projector with any item Avoid volatile liquids Moisture condensationDisposal Overview Shipping contentsRemote control operation Remote control batteriesCeiling mounting the projector Projector features Front and upper side view Projector exterior viewRear view Under viewControl panel Remote control Floor Front Choosing a locationCeiling Front Floor RearObtaining a preferred projected image size Installation for a 169 ratio screen Projection dimensionsHighest Installation for a 43 ratio screenLens Height HTo use the lens shift lever Shifting the projection lensPreparations Connecting Hdmi devicesReference Picture quality ComponentConnecting S-Video or video devices Connecting component-video devicesConnecting a monitor Connecting a computerConnect the projector to a computer with a VGA cable Preparations Turning the projector onSelecting an input source Using the OSD menuChanging Color Space Using a security cable lock Using the menusUse / to highlight the System Setup menu Securing the projectorSetting a password Utilizing the password functionIf you forget the password Changing the password Entering the password recall procedureDisabling the password function Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityTwo parallel sides Correcting picture distortionNo parallel sides Selecting a preset mode Using the preset and user modesFine-tuning the selected picture mode To fine-tune the picture modeResetting the picture mode Setting the User 1/User 2 modePress to highlight Load Settings From To reset the picture mode to the preset factory valuesFine-tuning the picture quality Selecting a color temperature Setting Black LevelAdvanced picture quality controls Controlling image claritySelecting a Gamma setting Setting a preferred color temperatureAdjusting Brilliant Color To set a preferred color temperatureTo adjust and store the settings Setting Film ModeColor Management Selecting the aspect ratio Setting 3D Comb FilterAbout the aspect ratio Image Using the entire resolution Using Panamorph lenses optionalAspect ratio Aspect ratio image 169 displayDisable Utilizing FAQ functionHiding the image Freezing the imageAdjusting the sound level Adjusting the soundTurning off the Power On/Off Ring Tone Muting the soundControlling the projector through a Lan environment Configuring the Lan Control SettingsControlling the projector remotely through a web browser If you are in a Dhcp environmentAuto Source Ii To switch input source, click on your desired signalMenu item Press Exit to go back to the remote network operationPress to highlight High Altitude Mode To activate High Altitude ModeOperating in a high altitude environment To display the PIP window Displaying more than one image source simultaneouslyHighlight PIP and press / to select On PIP function is effective at below source combinationsTurning the projector off On-Screen Display OSD structure On-Screen Display OSD menusMain menu Sub-menu Options Display System SetupInformation SetupPicture -- Advanced menu Picture -- Basic menuFunction Description Display menu Menu Settings Menu Position Sleep TimerClosed Caption Enable LanguageAdvanced Setup menu Information menu Cleaning the projector case Cleaning the lensCare of the projector Storing the projectorSetting Auto Off Setting Lamp Power as EconomicLamp information Getting to know the lamp hourReplacing the lamp Timing of replacing the lampStatus Message Reapply power and turn the projector back on Resetting the lamp timer Power Temp Lamp Status & Description IndicatorsProblem Cause Remedy TroubleshootingOptical SpecificationsElectrical TerminalsMm x 318 mm x 169 mm W x D x H DimensionsFormat Resolution Refresh rate Frequency Timing chartSupported timing for PC input KHz MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzSupported timing for Edtv and Hdtv via Component inputs Supported timing for Video and S-Video inputsCopyright WarrantyDisclaimer EEC statement for European users FCC statement for United States usersMIC statement Weee directiveEnglish