BenQ SP890 user manual Timing of replacing the lamp, Replacing the lamp, Status Message

Page 52

English

Timing of replacing the lamp

When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode. Go to http://lamp.BenQ.com for a replacement lamp.

The Lamp indicator light and Temperature warning light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator still lights up after turning the power back on, please contact your dealer. See "Indicators" on page 55 for details.

The following Lamp warning displays will remind you to change the lamp.

Status

Message

Install a new lamp for optimal performance. If the projector is

WARNING

normally run with Economic selected (See "Getting to know the lamp

 

hour" on page 51), you may continue to operate the projector until

NOTICE: Order replacement lamp

the next hour lamp warning appears.

Lamp > 2000hrs

Press ENTER to dismiss the message.

Order a new lamp at

lamp.benq.com

 

OK

 

 

It is strongly recommended that you replace the lamp at this age. The

WARNING

lamp is a consumable item. The lamp brightness diminishes with use.

 

This is normal lamp behavior. You can replace the lamp whenever

NOTICE: Replace lamp soon

you notice that the brightness level has significantly diminished.

Lamp > 2980hrs

Press ENTER to dismiss the message.

Order a new lamp at

lamp.benq.com

 

OK

 

 

The lamp MUST be replaced before the projector will operate

WARNING

normally.

NOTICE: Replace lamp now

Press ENTER to dismiss the message.

Lamp > 3000hrs

Lamp-usage time exceeded

 

Replace lamp (refer to User’s Manual)

 

then reset lamp timer.

 

Order a new lamp at

 

lamp.benq.com

 

OK

 

 

Replacing the lamp

•To reduce the risk of electrical shock, always turn the projector off and disconnect the power cable before changing the lamp.

•To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp.

•To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp glass that has shattered into sharp pieces.

•To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do not touch the empty lamp compartment when the lamp is removed.

•This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a proper manner.

52 Additional information

Page 51 Page 53
Image 52
Page 51 Page 53
Contents Welcome Table of contents Important safety instructions Do not cover the projector with any item Avoid volatile liquids Moisture condensationDisposal Shipping contents OverviewRemote control operation Remote control batteriesCeiling mounting the projector Projector features Projector exterior view Front and upper side viewRear view Under viewControl panel Remote control Choosing a location Floor FrontCeiling Front Floor RearObtaining a preferred projected image size Projection dimensions Installation for a 169 ratio screenInstallation for a 43 ratio screen HighestLens Height HShifting the projection lens To use the lens shift leverConnecting Hdmi devices PreparationsReference Picture quality ComponentConnecting component-video devices Connecting S-Video or video devicesConnecting a monitor Connecting a computerConnect the projector to a computer with a VGA cable Turning the projector on PreparationsSelecting an input source Using the OSD menuChanging Color Space Using the menus Using a security cable lockUse / to highlight the System Setup menu Securing the projectorSetting a password Utilizing the password functionIf you forget the password Changing the password Entering the password recall procedureDisabling the password function Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityTwo parallel sides Correcting picture distortionNo parallel sides Using the preset and user modes Selecting a preset modeFine-tuning the selected picture mode To fine-tune the picture modeSetting the User 1/User 2 mode Resetting the picture modePress to highlight Load Settings From To reset the picture mode to the preset factory valuesFine-tuning the picture quality Setting Black Level Selecting a color temperatureAdvanced picture quality controls Controlling image claritySetting a preferred color temperature Selecting a Gamma settingAdjusting Brilliant Color To set a preferred color temperatureTo adjust and store the settings Setting Film ModeColor Management Selecting the aspect ratio Setting 3D Comb FilterAbout the aspect ratio Using Panamorph lenses optional Image Using the entire resolutionAspect ratio Aspect ratio image 169 displayUtilizing FAQ function DisableHiding the image Freezing the imageAdjusting the sound Adjusting the sound levelTurning off the Power On/Off Ring Tone Muting the soundConfiguring the Lan Control Settings Controlling the projector through a Lan environmentControlling the projector remotely through a web browser If you are in a Dhcp environmentIi To switch input source, click on your desired signal Auto SourceMenu item Press Exit to go back to the remote network operationPress to highlight High Altitude Mode To activate High Altitude ModeOperating in a high altitude environment Displaying more than one image source simultaneously To display the PIP windowHighlight PIP and press / to select On PIP function is effective at below source combinationsTurning the projector off On-Screen Display OSD structure On-Screen Display OSD menusMain menu Sub-menu Options System Setup DisplaySetup InformationPicture -- Advanced menu Picture -- Basic menuFunction Description Display menu Sleep Timer Menu Settings Menu PositionClosed Caption Enable LanguageAdvanced Setup menu Information menu Cleaning the lens Cleaning the projector caseCare of the projector Storing the projectorSetting Lamp Power as Economic Setting Auto OffLamp information Getting to know the lamp hourReplacing the lamp Timing of replacing the lampStatus Message Reapply power and turn the projector back on Resetting the lamp timer Indicators Power Temp Lamp Status & DescriptionTroubleshooting Problem Cause RemedySpecifications OpticalElectrical TerminalsDimensions Mm x 318 mm x 169 mm W x D x HTiming chart Format Resolution Refresh rate FrequencySupported timing for PC input KHz MHzFormat Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHz Format Resolution Refresh rate Freq. KHz Pixel Freq MHzSupported timing for Edtv and Hdtv via Component inputs Supported timing for Video and S-Video inputsCopyright WarrantyDisclaimer FCC statement for United States users EEC statement for European usersMIC statement Weee directiveEnglish
Top Page Image Contents