BenQ SP890 Auto Source, Menu item, Ii To switch input source, click on your desired signal

Page 38

English

2.The remote network operation page opens. This page allows you to operate the projector as if you were using the remote control or control panel on the projector.

ii	i

i	•	Menu (Exit)		•	Blank
	•	Auto		•	Source		See "Remote control" on page 11 for details.
	•	(	)	•	(	)	See "Remote control" on page 11 for details.
	•	(	)	•	(	)
	•	(	)	•	(	)

	•	Enter					Activates the selected On-Screen Display (OSD)
	•	Enter					menu item.
							menu item.

iiTo switch input source, click on your desired signal.

The source list varies according to the connectors available on the projector. ''Video 1'' stands for the Video signal; ''S-Video 1'' stands for the S-Video signal.

The tools page allows you to manage the projector, configure the Lan control settings and secure access of remote network operation on this projector.

iiii

iiiv

v

i.You can name the projector, keep track of its location and the person in charge of it. ii. You can adjust the Lan Control Settings.

iii. Once set, access to the remote network operation on this projector has been password-protected. iv. Once set, access to the tools page has been password-protected.

After making the adjustments, press the Send button and the data will be saved in the projector.

v. Press Exit to go back to the remote network operation page.

38 Using the projector

Image 38

Contents Welcome Table of contents Important safety instructions Do not cover the projector with any item Disposal Moisture condensationAvoid volatile liquids Shipping contents OverviewCeiling mounting the projector Remote control batteriesRemote control operation Projector features Rear view Projector exterior viewFront and upper side view Under viewControl panel Remote control Ceiling Front Choosing a locationFloor Front Floor RearObtaining a preferred projected image size Projection dimensions Installation for a 169 ratio screenLens Installation for a 43 ratio screenHighest Height HShifting the projection lens To use the lens shift leverReference Picture quality Connecting Hdmi devicesPreparations ComponentConnecting component-video devices Connecting S-Video or video devicesConnect the projector to a computer with a VGA cable Connecting a computerConnecting a monitor Turning the projector on PreparationsChanging Color Space Using the OSD menuSelecting an input source Use / to highlight the System Setup menu Using the menusUsing a security cable lock Securing the projectorIf you forget the password Utilizing the password functionSetting a password Disabling the password function Entering the password recall procedureChanging the password Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityNo parallel sides Correcting picture distortionTwo parallel sides Fine-tuning the selected picture mode Using the preset and user modesSelecting a preset mode To fine-tune the picture modePress to highlight Load Settings From Setting the User 1/User 2 modeResetting the picture mode To reset the picture mode to the preset factory valuesFine-tuning the picture quality Advanced picture quality controls Setting Black LevelSelecting a color temperature Controlling image clarityAdjusting Brilliant Color Setting a preferred color temperatureSelecting a Gamma setting To set a preferred color temperatureColor Management Setting Film ModeTo adjust and store the settings About the aspect ratio Setting 3D Comb FilterSelecting the aspect ratio Aspect ratio Aspect ratio image Using Panamorph lenses optionalImage Using the entire resolution 169 displayHiding the image Utilizing FAQ functionDisable Freezing the imageTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Muting the soundControlling the projector remotely through a web browser Configuring the Lan Control SettingsControlling the projector through a Lan environment If you are in a Dhcp environmentMenu item Ii To switch input source, click on your desired signalAuto Source Press Exit to go back to the remote network operationOperating in a high altitude environment To activate High Altitude ModePress to highlight High Altitude Mode Highlight PIP and press / to select On Displaying more than one image source simultaneouslyTo display the PIP window PIP function is effective at below source combinationsTurning the projector off Main menu Sub-menu Options On-Screen Display OSD menusOn-Screen Display OSD structure System Setup DisplaySetup InformationFunction Description Picture -- Basic menuPicture -- Advanced menu Display menu Closed Caption Enable Sleep TimerMenu Settings Menu Position LanguageAdvanced Setup menu Information menu Care of the projector Cleaning the lensCleaning the projector case Storing the projectorLamp information Setting Lamp Power as EconomicSetting Auto Off Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Reapply power and turn the projector back on Resetting the lamp timer Indicators Power Temp Lamp Status & DescriptionTroubleshooting Problem Cause RemedyElectrical SpecificationsOptical TerminalsDimensions Mm x 318 mm x 169 mm W x D x HSupported timing for PC input Timing chartFormat Resolution Refresh rate Frequency KHz MHzSupported timing for Edtv and Hdtv via Component inputs Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Video and S-Video inputsDisclaimer WarrantyCopyright MIC statement FCC statement for United States usersEEC statement for European users Weee directiveEnglish