BenQ SP890 user manual Resetting the lamp timer

Page 54

English

Resetting the lamp timer

Do not reset the lamp timer if the lamp has not been replaced as this could cause damage.

1.After the start-up logo, press MENU on the projector or MENU/EXIT on the remote control, and then press / until the Advanced Setup menu is highlighted.

2.Press to highlight Lamp Settings and press ENTER. The Lamp Settings page is displayed.

3.Highlight Reset Lamp Timer and press ENTER. A warning message is displayed asking if you want to reset the lamp timer. Highlight Reset and press ENTER. The lamp time will be reset to "0".

Advanced Setup

Lamp Settings	ENTER
HDMI Settings
Baud Rate	115200
Test Pattern
High Altitude Mode	Off
Audio Settings
Password
Lan Control Settings
Reset All Settings
Expert Mode
Direct Power On	Off
S-Video	EXIT Back

Lamp Settings

Lamp Power	Normal
Reset Lamp Timer	ENTER
Equivalent Lamp Hour
	EXIT Back

WARNING

Reset Lamp Timer?

Reset Cancel

54 Additional information

Image 54

Contents Welcome Table of contents Important safety instructions Do not cover the projector with any item Moisture condensation Avoid volatile liquidsDisposal Shipping contents OverviewRemote control batteries Remote control operationCeiling mounting the projector Projector features Rear view Projector exterior viewFront and upper side view Under viewControl panel Remote control Ceiling Front Choosing a locationFloor Front Floor RearObtaining a preferred projected image size Projection dimensions Installation for a 169 ratio screenLens Installation for a 43 ratio screenHighest Height HShifting the projection lens To use the lens shift leverReference Picture quality Connecting Hdmi devicesPreparations ComponentConnecting component-video devices Connecting S-Video or video devicesConnecting a computer Connecting a monitorConnect the projector to a computer with a VGA cable Turning the projector on PreparationsUsing the OSD menu Selecting an input sourceChanging Color Space Use / to highlight the System Setup menu Using the menusUsing a security cable lock Securing the projectorUtilizing the password function Setting a passwordIf you forget the password Entering the password recall procedure Changing the passwordDisabling the password function Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityCorrecting picture distortion Two parallel sidesNo parallel sides Fine-tuning the selected picture mode Using the preset and user modesSelecting a preset mode To fine-tune the picture modePress to highlight Load Settings From Setting the User 1/User 2 modeResetting the picture mode To reset the picture mode to the preset factory valuesFine-tuning the picture quality Advanced picture quality controls Setting Black LevelSelecting a color temperature Controlling image clarityAdjusting Brilliant Color Setting a preferred color temperatureSelecting a Gamma setting To set a preferred color temperatureSetting Film Mode To adjust and store the settingsColor Management Setting 3D Comb Filter Selecting the aspect ratioAbout the aspect ratio Aspect ratio Aspect ratio image Using Panamorph lenses optionalImage Using the entire resolution 169 displayHiding the image Utilizing FAQ functionDisable Freezing the imageTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Muting the soundControlling the projector remotely through a web browser Configuring the Lan Control SettingsControlling the projector through a Lan environment If you are in a Dhcp environmentMenu item Ii To switch input source, click on your desired signalAuto Source Press Exit to go back to the remote network operationTo activate High Altitude Mode Press to highlight High Altitude ModeOperating in a high altitude environment Highlight PIP and press / to select On Displaying more than one image source simultaneouslyTo display the PIP window PIP function is effective at below source combinationsTurning the projector off On-Screen Display OSD menus On-Screen Display OSD structureMain menu Sub-menu Options System Setup DisplaySetup InformationPicture -- Basic menu Picture -- Advanced menuFunction Description Display menu Closed Caption Enable Sleep TimerMenu Settings Menu Position LanguageAdvanced Setup menu Information menu Care of the projector Cleaning the lensCleaning the projector case Storing the projectorLamp information Setting Lamp Power as EconomicSetting Auto Off Getting to know the lamp hourTiming of replacing the lamp Replacing the lampStatus Message Reapply power and turn the projector back on Resetting the lamp timer Indicators Power Temp Lamp Status & DescriptionTroubleshooting Problem Cause RemedyElectrical SpecificationsOptical TerminalsDimensions Mm x 318 mm x 169 mm W x D x HSupported timing for PC input Timing chartFormat Resolution Refresh rate Frequency KHz MHzSupported timing for Edtv and Hdtv via Component inputs Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Supported timing for Video and S-Video inputsWarranty CopyrightDisclaimer MIC statement FCC statement for United States usersEEC statement for European users Weee directiveEnglish