D-Link DP-802 IP Address Range End, IP Lease Time, IP Reserve Table, Default Value 1440 24 hours

Page 63

IP Address Range -> End

This is the second of the DHCP IP address range settings.

Options: Any IP address within the three reserved IP ranges. The IP address used must correlate with the IP set in the Beginning range setting.

Default Value: 192.168.100.150

Description: This setting indicates the end of the range of IP addresses available for DHCP use in assigning IPs. It is paired with the previous setting to create an address range.

IP Lease Time

Options: An amount of time, measured in minutes, from 5 to 65535.

Default Value: 1440 (24 hours)

Description: Dynamically assigned addresses can be peri- odically “refreshed” by a DHCP server. The IP Lease Time setting allows you to set that time limit. If a time is entered in this setting, each dynamically assigned address will be re- cycled at the end of the lease time.

IP Reserve Table

Options: Local IP Address, MAC Address (a maximum of 16 separate line entries).

Default Value: (none)

Description: The IP reserve table specifies ownership of par- ticular IP addresses by particular stations or servers

Configuration Settings

51

Image 63

Contents DP-802 NWay Internet/Print Server User’s Guide Wichtige Sicherheitshinweise Page Limited Warranty Limitation of Warranties Limitation of Liability Vcci a Warning Table of Contents Print Server Setup WAN Port Configuration Specifications Glossary Index Getting Started Quick InstallationQuick Installation Configuration Mandatory Settings for Internet Access Overview of the User’s Guide IntroductionAbout This Guide AudienceIntroduction Product Description Product FeaturesInternet Server Technology Non-Internet Implementations Introduction Unpacking InstallationOne lpr User’s Guide Desktop / Shelf InstallationPort Description Wall InstallationRJ-45 LAN LED DescriptionSerial WAN Parallel PrinterLink/Rx Pw/TxNormal LED Flash Pattern Connecting to the Local NetworkLAN Connection Connecting to the Internet Connecting Power Connecting PowerInternet Server Setup Using the Default Address Setting IP AddressesDefault Addressing Example Using Your Own Address Settings Using Telnet to Configure the Server Using a Browser to Configure the Server Minimum Configuration Default Value Must Be User Modified? Yes DNS IP AddressISP Account Phone Number Default Value none Must Be User Modified? Yes Default Value noneISP Account User ID ISP Account Password Prompt Keyin Username Stepanka Password Abcd Choice Login ScriptOperation ∙ DNS Domain Name Service an IP address provided by your ISPPrint Server Features Print Server SetupConnecting the Print Server NetBEUIAppleTalk MacOS EtherTalk Print Server Configuration Print Server Setup Page Navigation Controls Configuration SettingsLocal LAN IP Address System ConfigurationDefault Value Must Be User Modified? No Server NameLocal LAN Subnet Mask Default ValueOptions sub-menus Operation ModeDefault Value 30 minutes Must Be User Modified? No Maximum Idle TimeChange Password Line Type WAN Port ConfigurationDefault Value Dialup Default Value 115200 bpsISP Account User ID ISP Account IP Address Modem AT CommandsOptions sub-settings Dial Prefix String Atdt defaultPrompt Keyin Username Nick Password Abcd Choice Parallel Port Port Name Parallel Port Speed Parallel Port PJL PrinterNetBEUI Workgroup Name AppleTalk Printer Type Default Value LaserWriterDefault Value Level NetBEUI Maximum Connected Sta- tionsDhcp Server Configuration Default Value StandardAppleTalk Font Group Enable Options Yes/No Default Value YesIP Address Range Start IP Reserve Table Default Value 1440 24 hoursIP Address Range End IP Lease TimeLocal IP Address Server Address ConfigurationProtocol Dial-up Schedule Advanced Control ConfigurationManager Server IP Address Log and FilterHoliday Table Routing Table Filter NetBIOS over TCP/IP Display InformationDisplaying Information Dhcp Server Status ToolsSave Configuration Troubleshooting DP-802 LED Post Error Indication TableSystem Post WAN Device Installation ProblemsPrint Server Station Configuration ProblemsOperating Problems Page General SpecificationsEnvironmental and Physical Basic AT Command Set Modem AT CommandsModem AT Commands Hook Switch Sn? Command Var Description Extended AT& Command SetModem AT Commands Serial Port Port PinoutsRJ-45 Port Parallel PortPort Pinouts RJ-45 Twisted-Pair Cabling Active Pinout Configuration Address Glossary100Mbps 10MbpsCollision Domain BandwidthCategory 3, 4 CollisionIn-band EthernetFast Ethernet HubLeased-Line MbpsTelnet UTP/STP Twisted-pairAppleTalk IndexPinout TCP/IP Offices Internet/Print Server User’s Guide Registration Card