Agilent Technologies 8722ET, ES, 8720ET, 8719ET quick start Plotter Port

Page 18

Installing Your Analyzer

STEP 4. Conﬁgure the Analyzer

3.Press SET ADDRESSES and then choose either PRINTER PORT or PLOTTER PORT , depending on your printer/plotter device. Or, if you are plotting

your ﬁles to disk, press SET ADDRESSES PLOTTER PORT DISK .

4.Press the key that corresponds to your printer or plotter interface: GPIB , PARALLEL (parallel port), or SERIAL (serial port).

NOTE	The plotter menu is shown as an example. It will only appear if you select
			. Similar interface choices will appear if you select
	PLOTTER PORT		. Similar interface choices will appear if you select
		.
	PRINTER PORT	.

• If you select GPIB , the GPIB address selection is active. Enter the GPIB address of your printer or plotter,

followed by x1.

• If you have already selected the

PARALLEL [COPY] choice for the parallel-port conﬁguration, you must also select PARALLEL in this menu in order to generate a hardcopy.

1-12

Chapter 1

Image 18

Contents Installation and Quick Start Guide Part Number Print Date FebruaryPage Certiﬁcation General Safety Considerations How to Use This Guide Documentation Map Contents Installing Your Analyzer Introduction Verify the Shipment Item Number Part Number Description Familiarize Yourself with the Analyzer Front and Rear Panels Analyzer Front PanelAnalyzer Rear Panel Test SequenceMeet Electrical and Environmental Requirements Meet Electrical and Environmental Requirements Conﬁgure the Analyzer To Conﬁgure the Standard Analyzer To Conﬁgure the Analyzer with Printers or Plotters Plotter Port Conﬁgure the Analyzer Thinkjet Deskjet SET Clock To Conﬁgure the Analyzer for Bench Top or Rack Mount Use To Attach Front Handles to the Analyzer Standard Conﬁgure the Analyzer Conﬁgure the Analyzer Verify the Analyzer Operation To View the Installed Options To Initiate the Analyzer Self-Test Service Menu Tests To Run the Operators CheckTo Test the Transmission Mode TransmissnTo Test the Reﬂection Mode Meas Reﬂ REV S22 B/RDescription Eeprom Backup Disk ProcedureBack Up the Eeprom Disk EquipmentBack Up the Eeprom Disk Quick Start Learning How to Make Measurements Quick Start Learning How to Make Measurements Analyzer Front Panel Analyzer Front PanelAnalyzer Front Panel Measure the device Measurement ProcedureMake a measurement calibration Output measurement resultsLearning to Make Transmission Measurements Device Connections for a Transmission MeasurementPerform a measurement calibration Connections for a Thru Calibration StandardExample Measurement of Insertion Loss Press Return Define DISK-SAVE Measuring Other Transmission Characteristics Example Measurement of 3 dB BandwidthMeasuring Out-of-Band Rejection Example Measurement of Out-of-Band RejectionMeasuring Passband Flatness or Ripple Example Measurement of Passband Flatness or RippleLearning to Make Reﬂection Measurements = Γ= 1 + ρ / 1 − ρ Connections for Reﬂection Measurements Make a measurement calibration Measuring Return Loss 10 Example Measurement of Return Loss11 Example Measurement Title Measuring Other Reﬂection Characteristics Measuring Reﬂection CoefﬁcientMeasuring Standing Wave Ratio SWR 13 Example Standing-Wave-Ratio Measurement TraceMeasuring S11 and S22 or Reﬂection in a Polar Format Measuring S11 and S22 or Reﬂection in a Smith Chart Format 15 Example Impedance Measurement Trace If You Encounter a Problem Power-Up ProblemsIf the analyzer display does not light Data Entry Problems If there is no RF signal at the front-panel portNo RF Output If You Encounter a Problem Agilent Technologies Sales and Service Ofﬁces European Field OperationsIndex Index

Related manuals

Manual 63 pages 28.88 Kb