Agilent Technologies 8720ET, ES, 8722ET, 8719ET Meet Electrical and Environmental Requirements

Page 13

Installing Your Analyzer

STEP 3. Meet Electrical and Environmental Requirements

STEP 3. Meet Electrical and Environmental Requirements

1. Set the line-voltage selector to the		2. Ensure the available AC power source
position that corresponds to the AC power			meets the following requirements:
source.

		•	90–132 VAC
		• 47–66 Hz / 400 Hz (single phase)
			-or-
		•	198–265 VAC
		• 47–66 Hz (single phase)
		The analyzer power consumption is 350 VA
		maximum.

3. Ensure the operating environment meets		4. Verify that the power cable is not
the following requirements:			damaged, and that the power-source
			outlet provides a protective earth contact.

• 0 to 55 °C
• < 95% relative humidity at 40 °C
(non-condensing)
• < 15,000 feet (≈ 4,500 meters) altitude
Some analyzer performance parameters are
speciﬁed for 25 °C ±5 °C. Refer to the
Reference Guide for information on the
environmental compatibility of warranted
performance.

		WARNING
			Any interruption of the
			protective (grounding)
			conductor or
			disconnection of the
			protective earth terminal,
			can result in personal
			injury, or may damage the
			analyzer.

Chapter 1

1-7

Image 13

Contents Part Number Print Date February Installation and Quick Start GuidePage Certiﬁcation General Safety Considerations How to Use This Guide Documentation Map Contents Installing Your Analyzer Introduction Verify the Shipment Item Number Part Number Description Analyzer Front Panel Familiarize Yourself with the Analyzer Front and Rear PanelsTest Sequence Analyzer Rear PanelMeet Electrical and Environmental Requirements Meet Electrical and Environmental Requirements Conﬁgure the Analyzer To Conﬁgure the Standard Analyzer To Conﬁgure the Analyzer with Printers or Plotters Plotter Port Conﬁgure the Analyzer Thinkjet Deskjet SET Clock To Conﬁgure the Analyzer for Bench Top or Rack Mount Use To Attach Front Handles to the Analyzer Standard Conﬁgure the Analyzer Conﬁgure the Analyzer Verify the Analyzer Operation To View the Installed Options To Initiate the Analyzer Self-Test To Run the Operators Check Service Menu TestsTransmissn To Test the Transmission ModeMeas Reﬂ REV S22 B/R To Test the Reﬂection ModeBack Up the Eeprom Disk Eeprom Backup Disk ProcedureDescription EquipmentBack Up the Eeprom Disk Quick Start Learning How to Make Measurements Quick Start Learning How to Make Measurements Analyzer Front Panel Analyzer Front PanelAnalyzer Front Panel Make a measurement calibration Measurement ProcedureMeasure the device Output measurement resultsDevice Connections for a Transmission Measurement Learning to Make Transmission MeasurementsConnections for a Thru Calibration Standard Perform a measurement calibrationExample Measurement of Insertion Loss Press Return Define DISK-SAVE Example Measurement of 3 dB Bandwidth Measuring Other Transmission CharacteristicsExample Measurement of Out-of-Band Rejection Measuring Out-of-Band RejectionExample Measurement of Passband Flatness or Ripple Measuring Passband Flatness or Ripple= Γ Learning to Make Reﬂection Measurements= 1 + ρ / 1 − ρ Connections for Reﬂection Measurements Make a measurement calibration 10 Example Measurement of Return Loss Measuring Return Loss11 Example Measurement Title Measuring Reﬂection Coefﬁcient Measuring Other Reﬂection Characteristics13 Example Standing-Wave-Ratio Measurement Trace Measuring Standing Wave Ratio SWRMeasuring S11 and S22 or Reﬂection in a Polar Format Measuring S11 and S22 or Reﬂection in a Smith Chart Format 15 Example Impedance Measurement Trace Power-Up Problems If You Encounter a ProblemIf the analyzer display does not light If there is no RF signal at the front-panel port Data Entry ProblemsNo RF Output If You Encounter a Problem European Field Operations Agilent Technologies Sales and Service OfﬁcesIndex Index

Related manuals

Manual 63 pages 28.88 Kb