Agilent Technologies 8720ET, ES, 8722ET, 8719ET quick start Index

Page 61

Index

performing a measurement calibration, 2-15

REFLECTION port location, 2-4

requirements

electrical and environmental, 1-7

response function block keys location, 2-3

Return key, location, 2-3return loss

measuring, 2-16

S

Sales and Service Ofﬁces, 2-26shipment, verifying, 1-3smith chart, 2-21

smith chart format measuring, 2-21

softkeys, location, 2-3

standard analyzer conﬁguration, 1-10

standing wave ratio (SWR) measuring, 2-19

stimulus function block keys location, 2-3

T

transmission measurements, 2-6–2-12

3 dB bandwidth, 2-10

6 dB bandwidth, 2-11choosing the measurement

parameters, 2-6insertion loss, 2-8measuring insertion loss with

marker functions, 2-10measuring the device, 2-8out-of-band rejection, 2-11outputting measurement

results, 2-9passband ﬂatness, 2-12passband ripple, 2-12performing a measurement

calibration, 2-7TRANSMISSION port

location, 2-4troubleshooting, 2-23–2-25

V

verifying the shipment, 1-3

2

Index

Image 61

Contents Part Number Print Date February Installation and Quick Start GuidePage Certiﬁcation General Safety Considerations How to Use This Guide Documentation Map Contents Installing Your Analyzer Introduction Verify the Shipment Item Number Part Number Description Analyzer Front Panel Familiarize Yourself with the Analyzer Front and Rear PanelsTest Sequence Analyzer Rear PanelMeet Electrical and Environmental Requirements Meet Electrical and Environmental Requirements Conﬁgure the Analyzer To Conﬁgure the Standard Analyzer To Conﬁgure the Analyzer with Printers or Plotters Plotter Port Conﬁgure the Analyzer Thinkjet Deskjet SET Clock To Conﬁgure the Analyzer for Bench Top or Rack Mount Use To Attach Front Handles to the Analyzer Standard Conﬁgure the Analyzer Conﬁgure the Analyzer Verify the Analyzer Operation To View the Installed Options To Initiate the Analyzer Self-Test To Run the Operators Check Service Menu TestsTransmissn To Test the Transmission ModeMeas Reﬂ REV S22 B/R To Test the Reﬂection ModeBack Up the Eeprom Disk Eeprom Backup Disk ProcedureDescription EquipmentBack Up the Eeprom Disk Quick Start Learning How to Make Measurements Quick Start Learning How to Make Measurements Analyzer Front Panel Analyzer Front PanelAnalyzer Front Panel Make a measurement calibration Measurement ProcedureMeasure the device Output measurement resultsDevice Connections for a Transmission Measurement Learning to Make Transmission MeasurementsConnections for a Thru Calibration Standard Perform a measurement calibrationExample Measurement of Insertion Loss Press Return Define DISK-SAVE Example Measurement of 3 dB Bandwidth Measuring Other Transmission CharacteristicsExample Measurement of Out-of-Band Rejection Measuring Out-of-Band RejectionExample Measurement of Passband Flatness or Ripple Measuring Passband Flatness or Ripple= Γ Learning to Make Reﬂection Measurements= 1 + ρ / 1 − ρ Connections for Reﬂection Measurements Make a measurement calibration 10 Example Measurement of Return Loss Measuring Return Loss11 Example Measurement Title Measuring Reﬂection Coefﬁcient Measuring Other Reﬂection Characteristics13 Example Standing-Wave-Ratio Measurement Trace Measuring Standing Wave Ratio SWRMeasuring S11 and S22 or Reﬂection in a Polar Format Measuring S11 and S22 or Reﬂection in a Smith Chart Format 15 Example Impedance Measurement Trace Power-Up Problems If You Encounter a ProblemIf the analyzer display does not light If there is no RF signal at the front-panel port Data Entry ProblemsNo RF Output If You Encounter a Problem European Field Operations Agilent Technologies Sales and Service OfﬁcesIndex Index

Related manuals

Manual 63 pages 28.88 Kb