Agilent Technologies 8719ET, ES, 8720ET, 8722ET To Attach Front Handles to the Analyzer Standard

Page 23

Installing Your Analyzer

STEP 4. Conﬁgure the Analyzer

To Attach Front Handles to the Analyzer (Standard)

1.Ensure that the front handle kit is complete. 2. Remove the side trim strips.

•(2) front handles

•(6) screws

•(2) trim strips

NOTE	If any items are damaged or
	missing from the kit, contact the
	nearest Agilent Technologies
	sales or service ofﬁce to order a
	replacement kit. Items within
	the kit (handles, ﬂanges, screws,
	etc.) are not individually
	available.
3. Attach the handles to the sides of the front		4. Place the new trim strip over the screws on
panel, using three screws for each handle.		the handles.

WARNING If an instrument handle is damaged, you should replace it immediately. Damaged handles can break while you are moving or lifting the instrument and cause personal injury or damage to the instrument.

Chapter 1

1-17

Image 23

Contents Part Number Print Date February Installation and Quick Start GuidePage Certiﬁcation General Safety Considerations How to Use This Guide Documentation Map Contents Installing Your Analyzer Introduction Verify the Shipment Item Number Part Number Description Analyzer Front Panel Familiarize Yourself with the Analyzer Front and Rear PanelsTest Sequence Analyzer Rear PanelMeet Electrical and Environmental Requirements Meet Electrical and Environmental Requirements Conﬁgure the Analyzer To Conﬁgure the Standard Analyzer To Conﬁgure the Analyzer with Printers or Plotters Plotter Port Conﬁgure the Analyzer Thinkjet Deskjet SET Clock To Conﬁgure the Analyzer for Bench Top or Rack Mount Use To Attach Front Handles to the Analyzer Standard Conﬁgure the Analyzer Conﬁgure the Analyzer Verify the Analyzer Operation To View the Installed Options To Initiate the Analyzer Self-Test To Run the Operators Check Service Menu TestsTransmissn To Test the Transmission ModeMeas Reﬂ REV S22 B/R To Test the Reﬂection ModeEquipment Eeprom Backup Disk ProcedureBack Up the Eeprom Disk DescriptionBack Up the Eeprom Disk Quick Start Learning How to Make Measurements Quick Start Learning How to Make Measurements Analyzer Front Panel Analyzer Front PanelAnalyzer Front Panel Output measurement results Measurement ProcedureMake a measurement calibration Measure the deviceDevice Connections for a Transmission Measurement Learning to Make Transmission MeasurementsConnections for a Thru Calibration Standard Perform a measurement calibrationExample Measurement of Insertion Loss Press Return Define DISK-SAVE Example Measurement of 3 dB Bandwidth Measuring Other Transmission CharacteristicsExample Measurement of Out-of-Band Rejection Measuring Out-of-Band RejectionExample Measurement of Passband Flatness or Ripple Measuring Passband Flatness or Ripple= 1 + ρ / 1 − ρ Learning to Make Reﬂection Measurements= Γ Connections for Reﬂection Measurements Make a measurement calibration 10 Example Measurement of Return Loss Measuring Return Loss11 Example Measurement Title Measuring Reﬂection Coefﬁcient Measuring Other Reﬂection Characteristics13 Example Standing-Wave-Ratio Measurement Trace Measuring Standing Wave Ratio SWRMeasuring S11 and S22 or Reﬂection in a Polar Format Measuring S11 and S22 or Reﬂection in a Smith Chart Format 15 Example Impedance Measurement Trace If the analyzer display does not light If You Encounter a ProblemPower-Up Problems No RF Output Data Entry ProblemsIf there is no RF signal at the front-panel port If You Encounter a Problem European Field Operations Agilent Technologies Sales and Service OfﬁcesIndex Index

Related manuals

Manual 63 pages 28.88 Kb