ADTRAN NxT1 HSSI/V.35 user manual Read Security 5 Write Security

Page 36

Chapter 3. Operation

CONFIG

Read Security: 5; Write Security: 5

Contains parameters to include T1 data streams to the HSSI interface.

PRT

Displays the port number for the T1s mapped to the NxT1 HSSI interface. Ports 1 through 4 are the T1 interfaces located on the NxT1 HSSI Option Module. Ports 5 through 8 are T1s mapped to the NxT1 HSSI Option Module in the Dedicated Maps.

GROUP ASSOCIATION

Associates T1s (either mapped to this card and/or the on-board T1s) with the HSSI interface data stream. To add the T1 to the data stream, select the GROUP1 option.

SCRAMBLE

Enabling the SCRAMBLE option configures the NxT1 HSSI Module to prevent ones density violations when transmitting ADTRAN IMUX headers on a T1 circuit with AMI line coding.

Use extreme caution when disabling the SCRAMBLE option. ADTRAN recommends enabling the SCRAMBLE option for normal use.

HSSI MENUS

Read Security: 5

 

Provides status, configuration, and testing parameters for the 50-pin SCSI-

 

II HSSI interface.

 

STATUS

 

Read Security: 5

 

Displays the current loopback status of the HSSI interface

 

LOOPBACK

 

Displays the current loopback status of the HSSI interface. The fol-

 

lowing loopback options are possible (see Figure 3-4 on page 37):

 

LOCAL DTE LOOPBACK

 

A local DTE loopback occurs at the DTE port of the DCE, and is

 

used to test the link between the DTE and DCE (NxT1HSSI mod-

 

ule).

 

LOCAL LINE LOOPBACK

 

A local line loopback occurs in the IMUX engine and is used to test

 

functionality between the DTE and the IMUX engine.

 

REMOTE LINE LOOPBACK

 

A remote line loopback occurs at the T1 interface and is used to test

 

functionality between the DTE and the T1 interfaces.

36

NxT1 HSSI/V.35 Module User Manual

61200771L1-1

Page 35 Page 37
Image 36
Page 35 Page 37
Contents NxT1 HSSI/V.35 Module Page Save These Important Safety Instructions Affidavit Requirements for Connection to Digital Services Page Page SOC REN FIC Usoc Page Page Limited Product Warranty Customer Service, Product Support Information, and Training Post-Sale Support Table of Contents Appendix a Dedicated Maps Configuration List of Tables List of Tables List of Figures Figure A-1 Dedicated Maps MenuList of Figures Introduction NXT1 HSSI/V.35 Module OverviewFeatures NXT1 HSSI/V.35 Module SpecificationsFunctional Description Line or payload loopback Local and Remote Physical Description NxT1 HSSI/V.35 Option ModuleInstallation Before Installing the NXT1 HSSI/V.35 ModuleInstalling the NXT1 HSSI/V.35 Module Wiring Usoc RJ-48CPower UP and Initialization Failed Self-Test Operation AlarmsOperation OverviewTerminal Menu Structure Modules Read security Write security 3 Read securityModules/Menu on Nor has a module been manually enabled for this option slot Displays the assembly revision Sembly revisionDisplays the part number of the module Displays the serial number of the moduleAccess this menu item Write security 2 Read security Write security 4 Read security Option ModuleRead Security 5 Write Security Functionality between the DTE and the T1 interfacesLA and LB RX Rate and TX Rate Atlas Features Used with NXT1 HSSI/V.35 Module Options RestoreOperation Appendix a Dedicated Maps Configuration Write security3 Read security5Read security5 CREATE/EDIT Maps Write security3 Read security5Write security3 Read security Security level 3 Read securityNXT1 Hssi MenusT1 Trouble Code Service Appendix A. Dedicated Maps Configuration Index Index Index-48
Top Page Image Contents