ADIC 4000, 7000DLT Associated Documents, Explanation of Symbols and Notes

Page 14

Chapter 6	Troubleshooting and Diagnostic - Describes
	the troubleshooting and diagnostic
	techniques for the 4000/7000DLT Series.
Appendix A	Specifications - Outlines the specifications of
	the 4000/7000DLT Series.
Appendix B	Drive Configuration - Describes the specific
	information necessary to configure the
	4000/7000DLT Series.
Index

Associated Documents

None.

Explanation of Symbols and Notes

The following symbols and highlighted passages note important information. Detailed explanations of these symbols are found in Hazard Alert Messages on page 3-3.

Detailed explanations for the above symbols are provided in

Hazard Alert Messages on page 3-3.

<1> + <2>	Press these keys simultaneously.
Italics	Headline, e. g., Chapter Name, Description
Bold	Special Term, e. g., Utilities.
Courier	Terms appearing on the operating panel,
	switch position, e. g., ON, OFF

1-4 Introduction

62-0162-01

Image 14

Contents Installation and Operation Guide Copyright 1999 all rights reserved Contents Operation and Maintenance SafetyInstallation Troubleshooting and Diagnostic SpecificationIndex Drive ConfigurationRegulatory Notices Figures Viii Figures Tables Tables Introduction Introduction 62-0162-01 Organization OverviewIntended Audience Explanation of Symbols and Notes Associated DocumentsDescription Description 62-0162-01 Model DLTTape DLTTape Iiixt Model Drive Model Front Panel Controls and IndicatorsModel Sustained Maximum Description 24000DLT Front Panel Write Protected Rear Panel Controls and Connectors Control or Connector PurposeColor Length ModelCartridge Model Tape Other Requirements Scsi Host AdapterAdditional Items Scsi Interface CableApplication Software Cartridge RequirementsDescription 62-0162-01 Safety Safety 62-0162-01 Signal Word Definition Consequence Safety ConventionsSymbol Precautions Precautions Safety 62-0162-01 Installation Installation 62-0162-01 Unpacking and Inspecting Installing the Host AdapterConnecting the Interface Cable Connecting More than One 4000/ 7000DLT Series Aisy C hainedSetting the Scsi ID Check the Scsi Bus Termination Connecting Power and Turning On Installing the Backup SoftwareInstallation 62-0162-01 Operation Maintenance Operation and Maintenance 62-0162-01 Power-on Self-Test Drive State LED Indicator Displays and Drive Actions Drive StatusLCD Messages Drive StateLabel Color State Operating Condition Right Indicator Panel LEDDrive Operating Conditions Left Indicator Panel LED LCD Message Drive Operation LCD Messages 4Drive Operation LCD Messages 4Drive Operation LCD Messages Loading the Data Cartridge Lift up on the Cartridge Insert/Release HandleData Protection Tape in UseState Meaning Right Indicator PanelRemoving the Data Cartridge Cleaning the Tape Head Push the Cartridge Insert/Release Handle closedCleaning Tape LED It means You shouldCleaning Cycle LCD Messages Cleaning the Enclosure Troubleshooting Diagnostic Troubleshooting and Diagnostic 62-0162-01 Troubleshooting Chart Then You shouldProblem Chart Use Cleaning Tape LED Why the Use Cleaning Tape LED Gets Turned on High Humidity Troubleshooting and Diagnostic 62-0162-01 Specification Specification General Specification Table A-1Table A-1 Drive Configuration Drive Configuration DLT4000 Drives Drive Dependent ConfigurationScsi Bus Parity Figure B-3DLT7000 Tape Drive Connectors Right Side DLT7000 DriveScsi Bus Termination and Terminator Power Figure B-5DLT4000 Tape Drive Connectors right sideThen You Should Figure B-7DLT7000 Tape Drive Connectors right side DLT7000 DrivesDrive Configuration Regulatory Regulatory Notices FCC Notices U.S. Only Shielded CablesProduct Type IC Notice Canada OnlyEN 55022 Compliance Czech Republic Only CE NoticeVcci Notices Japan Only Index GB formatMotion Messages Index in-9 In-10 Index 62-0162-01