ADIC 7000DLT, 4000 installation and operation guide High Humidity

Page 65

High Humidity

To minimize the chance of condensation, please observe the following guidelines:

If you expose cartridges to temperatures outside the operating limits (5-40°C/40-113°F), stabilize them before you use them. To do this, leave the cartridges in the operating temperature for a minimum of two hours.

Avoid temperature problems by ensuring that the ventilator slots at the front of the drive and the grille on the bottom of the chassis are not obstructed so that the drive has adequate ventilation

Position the drive where the temperature is relatively stable, for example, away from open windows, fan heaters, and doors.

Avoid leaving cartridges in severe temperature conditions, for example, in a car standing in bright sunlight.

Avoid transferring data (reading from and writing to cartridges) when the temperature is changing by more than 10°C per hour.

High Humidity

6-7

 

 

 

 

Image 65
Contents Installation and Operation Guide Copyright 1999 all rights reserved Contents Operation and Maintenance SafetyInstallation Specification Troubleshooting and DiagnosticIndex Drive ConfigurationRegulatory Notices Figures Viii Figures Tables Tables Introduction Introduction 62-0162-01 Organization OverviewIntended Audience Associated Documents Explanation of Symbols and NotesDescription Description 62-0162-01 Model DLTTape DLTTape Iiixt Model Drive Model Front Panel Controls and IndicatorsModel Sustained Maximum Description 24000DLT Front Panel Write Protected Control or Connector Purpose Rear Panel Controls and ConnectorsColor Length ModelCartridge Model Tape Scsi Host Adapter Other RequirementsApplication Software Scsi Interface CableAdditional Items Cartridge RequirementsDescription 62-0162-01 Safety Safety 62-0162-01 Signal Word Definition Consequence Safety ConventionsSymbol Precautions Precautions Safety 62-0162-01 Installation Installation 62-0162-01 Unpacking and Inspecting Installing the Host AdapterConnecting the Interface Cable Aisy C hained Connecting More than One 4000/ 7000DLT SeriesSetting the Scsi ID Check the Scsi Bus Termination Installing the Backup Software Connecting Power and Turning OnInstallation 62-0162-01 Operation Maintenance Operation and Maintenance 62-0162-01 Power-on Self-Test Drive Status Drive State LED Indicator Displays and Drive ActionsDrive State LCD MessagesLabel Color State Operating Condition Right Indicator Panel LEDDrive Operating Conditions Left Indicator Panel LED LCD Message Drive Operation LCD Messages 4Drive Operation LCD Messages 4Drive Operation LCD Messages Lift up on the Cartridge Insert/Release Handle Loading the Data CartridgeTape in Use Data ProtectionState Meaning Right Indicator PanelRemoving the Data Cartridge Push the Cartridge Insert/Release Handle closed Cleaning the Tape HeadIt means You should Cleaning Tape LEDCleaning Cycle LCD Messages Cleaning the Enclosure Troubleshooting Diagnostic Troubleshooting and Diagnostic 62-0162-01 Then You should Troubleshooting ChartProblem Chart Use Cleaning Tape LED Why the Use Cleaning Tape LED Gets Turned on High Humidity Troubleshooting and Diagnostic 62-0162-01 Specification Specification Table A-1 General SpecificationTable A-1 Drive Configuration Drive Configuration DLT4000 Drives Drive Dependent ConfigurationScsi Bus Parity DLT7000 Drive Figure B-3DLT7000 Tape Drive Connectors Right SideFigure B-5DLT4000 Tape Drive Connectors right side Scsi Bus Termination and Terminator PowerThen You Should DLT7000 Drives Figure B-7DLT7000 Tape Drive Connectors right sideDrive Configuration Regulatory Regulatory Notices Shielded Cables FCC Notices U.S. OnlyIC Notice Canada Only Product TypeCE Notice EN 55022 Compliance Czech Republic OnlyVcci Notices Japan Only GB format IndexMotion Messages Index in-9 In-10 Index 62-0162-01