ADIC 7000DLT, 4000 installation and operation guide Setting the Scsi ID

Page 37

Setting the SCSI ID

Note

The SCSI ID has been factory preset to 0.

All devices on a SCSI bus must be set to a unique address.

Depending upon your setup, operating system and number of SCSI devices on the bus, you may have to change the SCSI address of the 4000/7000DLT Series. Each device on the bus must have its own unique address. See Figure 4-1 on page 4-4 and Figure 4-2.

3

S C S I ID

S w itc h

Figure 4-2

Note

All 4000/7000DLT Series models can be set to any SCSI ID between 0 and

7.The 7000DLT, a fast-wide SCSI-2 device, can be set to any SCSI ID between 0 and 15.

SCSI ID Switch

The SCSI ID switch is located on the rear of the 4000/7000DLT Series (see Figure 7). Use a small pointed object to press either the + button on the bottom, or the minus button on the top of the switch to select the proper ID.

Setting the SCSI ID	4-5

Image 37

Contents Installation and Operation Guide Copyright 1999 all rights reserved Contents Installation SafetyOperation and Maintenance Specification Troubleshooting and DiagnosticRegulatory Notices Drive ConfigurationIndex Figures Viii Figures Tables Tables Introduction Introduction 62-0162-01 Intended Audience OverviewOrganization Associated Documents Explanation of Symbols and NotesDescription Description 62-0162-01 Model DLTTape DLTTape Iiixt Model Sustained Maximum Front Panel Controls and IndicatorsModel Drive Model Description 24000DLT Front Panel Write Protected Control or Connector Purpose Rear Panel Controls and ConnectorsCartridge Model Tape ModelColor Length Scsi Host Adapter Other RequirementsApplication Software Scsi Interface CableAdditional Items Cartridge RequirementsDescription 62-0162-01 Safety Safety 62-0162-01 Symbol Safety ConventionsSignal Word Definition Consequence Precautions Precautions Safety 62-0162-01 Installation Installation 62-0162-01 Connecting the Interface Cable Installing the Host AdapterUnpacking and Inspecting Aisy C hained Connecting More than One 4000/ 7000DLT SeriesSetting the Scsi ID Check the Scsi Bus Termination Installing the Backup Software Connecting Power and Turning OnInstallation 62-0162-01 Operation Maintenance Operation and Maintenance 62-0162-01 Power-on Self-Test Drive Status Drive State LED Indicator Displays and Drive ActionsDrive State LCD MessagesDrive Operating Conditions Right Indicator Panel LEDLabel Color State Operating Condition Left Indicator Panel LED LCD Message Drive Operation LCD Messages 4Drive Operation LCD Messages 4Drive Operation LCD Messages Lift up on the Cartridge Insert/Release Handle Loading the Data CartridgeTape in Use Data ProtectionRemoving the Data Cartridge Right Indicator PanelState Meaning Push the Cartridge Insert/Release Handle closed Cleaning the Tape HeadIt means You should Cleaning Tape LEDCleaning Cycle LCD Messages Cleaning the Enclosure Troubleshooting Diagnostic Troubleshooting and Diagnostic 62-0162-01 Then You should Troubleshooting ChartProblem Chart Use Cleaning Tape LED Why the Use Cleaning Tape LED Gets Turned on High Humidity Troubleshooting and Diagnostic 62-0162-01 Specification Specification Table A-1 General SpecificationTable A-1 Drive Configuration Drive Configuration Scsi Bus Parity Drive Dependent ConfigurationDLT4000 Drives DLT7000 Drive Figure B-3DLT7000 Tape Drive Connectors Right SideFigure B-5DLT4000 Tape Drive Connectors right side Scsi Bus Termination and Terminator PowerThen You Should DLT7000 Drives Figure B-7DLT7000 Tape Drive Connectors right sideDrive Configuration Regulatory Regulatory Notices Shielded Cables FCC Notices U.S. OnlyIC Notice Canada Only Product TypeCE Notice EN 55022 Compliance Czech Republic OnlyVcci Notices Japan Only GB format IndexMotion Messages Index in-9 In-10 Index 62-0162-01