ADIC 7000DLT, 4000 Connecting Power and Turning On, Installing the Backup Software

Page 39

Connecting Power and Turning On

Note

Turning on the host computer first ensures that the SCSI bus terminators stabilize the bus signals before the tape drive is turned on.

Step 1 Plug the power cord into the back of the 4000/ 7000DLT Series.

Step 2 Plug the power cord from the 4000/7000DLT Series into a GROUNDED electrical outlet.

Step 3 Plug the power cord from your host system into the same GROUNDED electrical circuit if possible. Computers and peripherals should always share the same grounds.

Step 4 Turn ON the power to your host system.

Step 5 Turn the 4000/7000DLT Series power ON.

Installing the Backup Software

At this point, please refer to your backup software installation guide and install the backup software.

After you have completed installation of your 4000/7000DLT Series and the backup software, you should run a small backup/restore and compare to confirm that your unit is working correctly. See your software installation guide for additional information.

Connecting Power and Turning On	4-7

Image 39

Contents Installation and Operation Guide Copyright 1999 all rights reserved Contents Safety InstallationOperation and Maintenance Specification Troubleshooting and DiagnosticDrive Configuration Regulatory NoticesIndex Figures Viii Figures Tables Tables Introduction Introduction 62-0162-01 Overview Intended AudienceOrganization Associated Documents Explanation of Symbols and NotesDescription Description 62-0162-01 Model DLTTape DLTTape Iiixt Front Panel Controls and Indicators Model Sustained MaximumModel Drive Model Description 24000DLT Front Panel Write Protected Control or Connector Purpose Rear Panel Controls and ConnectorsModel Cartridge Model TapeColor Length Scsi Host Adapter Other RequirementsCartridge Requirements Scsi Interface CableApplication Software Additional ItemsDescription 62-0162-01 Safety Safety 62-0162-01 Safety Conventions SymbolSignal Word Definition Consequence Precautions Precautions Safety 62-0162-01 Installation Installation 62-0162-01 Installing the Host Adapter Connecting the Interface CableUnpacking and Inspecting Aisy C hained Connecting More than One 4000/ 7000DLT SeriesSetting the Scsi ID Check the Scsi Bus Termination Installing the Backup Software Connecting Power and Turning OnInstallation 62-0162-01 Operation Maintenance Operation and Maintenance 62-0162-01 Power-on Self-Test Drive Status Drive State LED Indicator Displays and Drive ActionsDrive State LCD MessagesRight Indicator Panel LED Drive Operating ConditionsLabel Color State Operating Condition Left Indicator Panel LED LCD Message Drive Operation LCD Messages 4Drive Operation LCD Messages 4Drive Operation LCD Messages Lift up on the Cartridge Insert/Release Handle Loading the Data CartridgeTape in Use Data ProtectionRight Indicator Panel Removing the Data CartridgeState Meaning Push the Cartridge Insert/Release Handle closed Cleaning the Tape HeadIt means You should Cleaning Tape LEDCleaning Cycle LCD Messages Cleaning the Enclosure Troubleshooting Diagnostic Troubleshooting and Diagnostic 62-0162-01 Then You should Troubleshooting ChartProblem Chart Use Cleaning Tape LED Why the Use Cleaning Tape LED Gets Turned on High Humidity Troubleshooting and Diagnostic 62-0162-01 Specification Specification Table A-1 General SpecificationTable A-1 Drive Configuration Drive Configuration Drive Dependent Configuration Scsi Bus ParityDLT4000 Drives DLT7000 Drive Figure B-3DLT7000 Tape Drive Connectors Right SideFigure B-5DLT4000 Tape Drive Connectors right side Scsi Bus Termination and Terminator PowerThen You Should DLT7000 Drives Figure B-7DLT7000 Tape Drive Connectors right sideDrive Configuration Regulatory Regulatory Notices Shielded Cables FCC Notices U.S. OnlyIC Notice Canada Only Product TypeCE Notice EN 55022 Compliance Czech Republic OnlyVcci Notices Japan Only GB format IndexMotion Messages Index in-9 In-10 Index 62-0162-01