ADIC 4000, 7000DLT Loading the Data Cartridge, Lift up on the Cartridge Insert/Release Handle

Page 52

Loading the Data Cartridge

Caution	Due to static the label or other items included in this
	package will occasionally cling to the DLT cartridge.
	package will occasionally cling to the DLT cartridge.
	Before loading into a drive, ensure that all other items from
	this package are separated from the cartridge.
	Never press in on the hub portion of the data cartridge.

Caution

Step 1 If you are planning to write data to, or erase data from,thecartridge,makesuretheWrite-Protectswitch on the cartridge is in the write-enabled position (all the way to the right).

A data cartridge can only be loaded when the Operate Handle LED is ON. Do not attempt to open the Cartridge Insert/Release Handle unless this LED is ON steady.

Step 2 Lift up on the Cartridge Insert/Release Handle.

Figure 5-1Loading a Data Cartridge

5-12 Operation and Maintenance

62-0162-01

Image 52

Contents Installation and Operation Guide Copyright 1999 all rights reserved Contents Installation SafetyOperation and Maintenance Troubleshooting and Diagnostic SpecificationRegulatory Notices Drive ConfigurationIndex Figures Viii Figures Tables Tables Introduction Introduction 62-0162-01 Intended Audience OverviewOrganization Explanation of Symbols and Notes Associated DocumentsDescription Description 62-0162-01 Model DLTTape DLTTape Iiixt Model Sustained Maximum Front Panel Controls and IndicatorsModel Drive Model Description 24000DLT Front Panel Write Protected Rear Panel Controls and Connectors Control or Connector PurposeCartridge Model Tape ModelColor Length Other Requirements Scsi Host AdapterScsi Interface Cable Application SoftwareAdditional Items Cartridge RequirementsDescription 62-0162-01 Safety Safety 62-0162-01 Symbol Safety ConventionsSignal Word Definition Consequence Precautions Precautions Safety 62-0162-01 Installation Installation 62-0162-01 Connecting the Interface Cable Installing the Host AdapterUnpacking and Inspecting Connecting More than One 4000/ 7000DLT Series Aisy C hainedSetting the Scsi ID Check the Scsi Bus Termination Connecting Power and Turning On Installing the Backup SoftwareInstallation 62-0162-01 Operation Maintenance Operation and Maintenance 62-0162-01 Power-on Self-Test Drive State LED Indicator Displays and Drive Actions Drive StatusLCD Messages Drive StateDrive Operating Conditions Right Indicator Panel LEDLabel Color State Operating Condition Left Indicator Panel LED LCD Message Drive Operation LCD Messages 4Drive Operation LCD Messages 4Drive Operation LCD Messages Loading the Data Cartridge Lift up on the Cartridge Insert/Release HandleData Protection Tape in UseRemoving the Data Cartridge Right Indicator PanelState Meaning Cleaning the Tape Head Push the Cartridge Insert/Release Handle closedCleaning Tape LED It means You shouldCleaning Cycle LCD Messages Cleaning the Enclosure Troubleshooting Diagnostic Troubleshooting and Diagnostic 62-0162-01 Troubleshooting Chart Then You shouldProblem Chart Use Cleaning Tape LED Why the Use Cleaning Tape LED Gets Turned on High Humidity Troubleshooting and Diagnostic 62-0162-01 Specification Specification General Specification Table A-1Table A-1 Drive Configuration Drive Configuration Scsi Bus Parity Drive Dependent ConfigurationDLT4000 Drives Figure B-3DLT7000 Tape Drive Connectors Right Side DLT7000 DriveScsi Bus Termination and Terminator Power Figure B-5DLT4000 Tape Drive Connectors right sideThen You Should Figure B-7DLT7000 Tape Drive Connectors right side DLT7000 DrivesDrive Configuration Regulatory Regulatory Notices FCC Notices U.S. Only Shielded CablesProduct Type IC Notice Canada OnlyEN 55022 Compliance Czech Republic Only CE NoticeVcci Notices Japan Only Index GB formatMotion Messages Index in-9 In-10 Index 62-0162-01