ADIC 7000DLT Drive Dependent Configuration, Scsi Bus Parity, DLT4000 Drives

Page 73

Drive Dependent Configuration

This section describes the options you can select by installing jumpers on the DLT Tape Drives.

SCSI Bus Parity

The following paragraphs detail information about parity selection on different drive types.

DLT4000 Drives

If your host computer system does not generate SCSI bus parity, you can disable parity checking in the DLT drives by installing a jumper over two pins on the SCSI ID connector. See Figure B-1 for location of the connector.

F ro n t

B e z e l

L e ft S id e

S C S I ID

C o n n e c to r

Figure B-1DLT4000 Tape Drive Connectors (Left Side)

Figure B-2 shows which pins of the SCSI ID connector have to be jumpered to disable parity.

Disable

Parity

Figure B-2Disable Parity Pins on SCSI ID Connector

Drive Dependent Configuration	B-3

Image 73

Contents Installation and Operation Guide Copyright 1999 all rights reserved Contents Installation SafetyOperation and Maintenance Specification Troubleshooting and DiagnosticRegulatory Notices Drive ConfigurationIndex Figures Viii Figures Tables Tables Introduction Introduction 62-0162-01 Intended Audience OverviewOrganization Associated Documents Explanation of Symbols and NotesDescription Description 62-0162-01 Model DLTTape DLTTape Iiixt Model Sustained Maximum Front Panel Controls and IndicatorsModel Drive Model Description 24000DLT Front Panel Write Protected Control or Connector Purpose Rear Panel Controls and ConnectorsCartridge Model Tape ModelColor Length Scsi Host Adapter Other RequirementsApplication Software Scsi Interface CableAdditional Items Cartridge RequirementsDescription 62-0162-01 Safety Safety 62-0162-01 Symbol Safety ConventionsSignal Word Definition Consequence Precautions Precautions Safety 62-0162-01 Installation Installation 62-0162-01 Connecting the Interface Cable Installing the Host AdapterUnpacking and Inspecting Aisy C hained Connecting More than One 4000/ 7000DLT SeriesSetting the Scsi ID Check the Scsi Bus Termination Installing the Backup Software Connecting Power and Turning OnInstallation 62-0162-01 Operation Maintenance Operation and Maintenance 62-0162-01 Power-on Self-Test Drive Status Drive State LED Indicator Displays and Drive ActionsDrive State LCD MessagesDrive Operating Conditions Right Indicator Panel LEDLabel Color State Operating Condition Left Indicator Panel LED LCD Message Drive Operation LCD Messages 4Drive Operation LCD Messages 4Drive Operation LCD Messages Lift up on the Cartridge Insert/Release Handle Loading the Data CartridgeTape in Use Data ProtectionRemoving the Data Cartridge Right Indicator PanelState Meaning Push the Cartridge Insert/Release Handle closed Cleaning the Tape HeadIt means You should Cleaning Tape LEDCleaning Cycle LCD Messages Cleaning the Enclosure Troubleshooting Diagnostic Troubleshooting and Diagnostic 62-0162-01 Then You should Troubleshooting ChartProblem Chart Use Cleaning Tape LED Why the Use Cleaning Tape LED Gets Turned on High Humidity Troubleshooting and Diagnostic 62-0162-01 Specification Specification Table A-1 General SpecificationTable A-1 Drive Configuration Drive Configuration Scsi Bus Parity Drive Dependent ConfigurationDLT4000 Drives DLT7000 Drive Figure B-3DLT7000 Tape Drive Connectors Right SideFigure B-5DLT4000 Tape Drive Connectors right side Scsi Bus Termination and Terminator PowerThen You Should DLT7000 Drives Figure B-7DLT7000 Tape Drive Connectors right sideDrive Configuration Regulatory Regulatory Notices Shielded Cables FCC Notices U.S. OnlyIC Notice Canada Only Product TypeCE Notice EN 55022 Compliance Czech Republic OnlyVcci Notices Japan Only GB format IndexMotion Messages Index in-9 In-10 Index 62-0162-01