Cisco TelePresence System Codec C90 and Profile 65” Dual using C90
Contents | Introduction | Web interface | Advanced configuration | Password protection | Appendices |
Administrator guide
Contact us
Conference [1..1] MicUnmuteOnDisconnect
Determine if the microphones shall be unmuted automatically when all calls are disconnected. In a meeting room or other shared resource this could be done to prepare the system for the next user.
Requires user role: ADMIN
Value space: <On/Off>
On:
Off:If muted, let the microphones remain muted after the call is disconnected.
Example: Conference 1 MicUnmuteOnDisconnect: On
Conference [1..1] DoNotDisturb Mode
Determine if there should be an alert on incoming calls.
Requires user role: USER
Value space: <On/Off>
On: On: All incoming calls will be rejected, with no alert. The calling side will receive a busy signal when trying to call the codec. A message will display on screen, telling that Do not disturb is turned on, together with an option to turn off the Do not disturb. When turning off the Do not disturb mode you will see a list of the calls that have been rejected.
Off:The incoming calls will be alerted.
Example: DoNotDisturb Mode: Off
Conference [1..1] FarEndControl Mode
Lets you decide if the remote side (far end) should be allowed to select your video sources and control your local camera (pan, tilt, zoom).
Requires user role: ADMIN
Value space: <On/Off>
On: Allows the far end to be able to select your video sources and control your local camera (pan, tilt, zoom). You will still be able to control your camera and select your video sources as normal.
Off:Do not allow the far end to select your video sources or to control your local camera (pan, tilt, zoom).
Example: Conference 1 FarEndControl Mode: On
Conference [1..1] Encryption Mode
Set the conference encryption mode. A padlock with the text "Encryption On" or "Encryption Off" displays on screen, for a few seconds, when the conference starts.
Requires user role: ADMIN
Value space: <BestEffort/On/Off>
BestEffort: The system will use encryption whenever possible.
>In Point to point calls: If the far end system supports encryption
>In MultiSite calls: In order to have encrypted MultiSite conferences, all sites must support encryption. If not, the conference will be unencrypted.
On: The system will only allow calls that are encrypted.
Off:The system will not use encryption.
Example: Conference 1 Encryption Mode: BestEffort
Conference [1..1] DefaultCall Protocol
Set the Default Call Protocol to be used when placing calls from the system.
Requires user role: ADMIN
Value space: <H323/SIP>
H.323: Select H.323 to ensure that calls are set up as H.323 calls.
SIP: Select SIP to ensure that calls are set up as SIP calls.
Example: Conference 1 DefaultCall Protocol: H323
Conference [1..1] DefaultCall Rate
Set the Default Call Rate to be used when placing calls from the system.
Requires user role: ADMIN
Value space: <64..6000>
Range:
Example: Conference 1 DefaultCall Rate: 768
Conference [1..1] FarEndControl SignalCapability
Set the far end control (H.224) signal capability mode.
Requires user role: ADMIN
Value space: <On/Off>
On: Enable the far end control signal capability.
Off: Disable the far end control signal capability.
Example: Conference 1 FarEndControl SignalCapability: On
Conference [1..1] MaxTransmitCallRate
Specify the maximum transmit call rate to be used when placing or receiving calls.
Requires user role: ADMIN
Value space: <64..6000>
Range: Select a value from 64 to 6000 kbps.
Example: Conference 1 MaxTransmitCallRate: 6000
D14635.05 Profile C90 and Codec C90 Administrator Guide TC4.1, February 2011. | 40 | www.cisco.com |
Copyright © |