Lathem PC400TX manual Limited One-Year Limited Warranty

Page 36

30 - PC400 Terminal Installation & User’s Guide

Limited One-Year Limited Warranty

Lathem warrants the hardware products described in this guide against defects in material and workmanship for a period of one year from date of original purchase from Lathem or from an authorized Lathem reseller. The conditions of this warranty and the extent of the responsibility of Lathem Time Corporation (“Lathem”) under this warranty are listed below.

1.This warranty will become void when service performed by anyone other than an approved Lathem warranty service dealer results in damage to the product.

2.This warranty does not apply to any product which has been subject to abuse, neglect, or accident, or which has had the serial number altered or removed, or which has been connected, installed, adjusted, or repaired other than in accordance with instructions furnished by Lathem.

3.This warranty does not cover dealer labor cost for removing and reinstalling the machine for repair, or any expendable parts that are readily replaced due to normal use.

4.The sole responsibility of Lathem under this warranty shall be limited to repair of this product, or replacement thereof, at the sole discretion of Lathem.

5.If it becomes necessary to send the product or any defective part to Lathem or any authorized service dealer, the product must be shipped in its original carton or equivalent, fully insured with shipping charges prepaid. Lathem will not assume any responsibility for any loss or damage incurred in shipping.

6.WARRANTY DISCLAIMER AND LIMITATION OF LIABILITY: Except only the limited express warranty set forth above, the products are sold with no expressed or implied warranties of any kind, and the implied warranties of merchantability and fitness for a particular purpose are hereby expressly disclaimed. No warranties are given with respect to products purchased other than from Lathem or an authorized Lathem reseller and any such products are purchased "as is, with all faults." In no event will Lathem be liable for any direct, indirect, special, incidental or consequential damages arising out of or in connection with the delivery, use or inability to use, or performance of this product. In the event any limited remedy given herein shall be deemed to have failed of its essential purpose, Lathem's maximum liability shall be to refund the purchase price upon return of the product.

7.Proof of date of purchase from Lathem or an authorized Lathem reseller is required for warranty service on this product.

8.This Warranty grants specific legal rights. Additional legal rights, which may vary by locale, may also apply.

9.Should any difficulties arise with the performance of this product during warranty, or with any Lathem authorized service centers, contact Lathem Time at the address below.

Lathem Time

200 Selig Drive, SW, Atlanta, GA 30336

404-691-0405

www.lathem.com

Copyright © 2003 Lathem Time Corporation. All rights reserved.

Revised 01-15-2008

Document number: USG0037I

Image 36
Contents Installation & User’s Guide PC400 & PC400TX TerminalFor Units Equipped with AN Internal Modem Support Information Getting HelpSupport Agreements N T E N T S Page Page Features and Specifications WelcomePower Surges and Spikes Main Application Files TERMMGR.EXEWall Mount To install the back box Mount the ClockPage Desktop Mount To install the back box Connect the Communication Cables RS-232 ConnectionsTo make an RS232 connection RS-485 Connections To make an RS485 connectionModem Connections optional To make a Modem connectionPC400TX TCP/IP Connections optional To make a TCP/IP connectionTo connect your signaling devices power source Bell Relay ConnectionsMaximum of 4 Bells / Horns Setup the Clock Starting the Terminal Setup ModeTo power up the clock To start the Terminal Setup Mode Select 0 PM / 1 AMPIN Entry SetupMode Using the Clock To punch using a badgeTo transfer Supervisor Mode Schedule OverrideManual Bell Ring Wiring Diagrams RS-232 to HostRS-485 Network Multi Drop Network using the SWIFT485+ PC400 Terminal Block Diagram Installing a Modem Module in the PC400 ¾ Remove the PayClock 400 Terminal from the Back BoxPage Installing a TCP/IP 10Base T Module in the PC400 ¾ Install the 10Base T ModulePC400 Terminal Installation & User’s Guide Replacing an Existing PayClock 2000 or PC100 PC400 Terminal Installation & User’s Guide Troubleshoot the Clock Ground screw and ground wire attached to back box Limited One-Year Limited Warranty Index