Casio AX200 manual Proximity Readers

Page 115

www.axxessid.com

Installation & User Guide

Proximity Readers

Honeywell proximity readers have been designed to be installed for use with access control systems. The following instructions outline the connections between the reader and the AX200 access control system as well as the software configurations that need to be carried out in order to make the system ready to operate.

How to connect the reader to the host

The reader is supplied with an 18-inch pigtail, having a 6-conductor

cable. To connect the reader to the AX200 system, perform the following steps:

1.If there is a connector on the end of the cable (used during manufacture for testing purposes), cut it off. Prepare the reader cable by cutting the cable jacket back 1.25 inches and strip the wires 0.5 inch.

2.The reader is connected directly to the AX100 controller. The table below shows the connections on the AX100 controller and the corresponding wires on the Honeywell proximity reader.

Colour	AX100
Red	12V
Black	0V
White	D1
Green	D0
Brown	LED

When using a separate power supply for the reader, power supply and the AX100 must have a common ground.

3.Do not connect the Tamper (purple) lead to the AX100.

4.Trim and cover all conductors that are not used.

Software Configuration

Once the reader & the AX100 controller have been connected to the AX200 unit you should be able to see it on the controllers menu on the right hand side of the main screen. In order to program a valid card with the ability to have access through a Honeywell proximity reader you need to choose the correct format.

1.On the main screen click on the Format & Statistics.

2.Under the Card Matching tab press “Select Reader”

3.Choose the appropriate reader from the list and present the card to the reader

4.The software will automatically display the card number, Facility Code and the possible card formats.

AX200 Installation & User Guide – July 2007

1 1 5

Image 115

Contents AX200 & i-BOX Email info@axxessid.com C e n s e a g r e e m e n t N t e n t s Photo Photo ID Add a Photo Rollback 109 103105 108AX200 Software Setup 2 0 0 InstallationInstallation & User Guide Installation & User Guide IP Address D e f i n i t i o n s a p p l i c a b l e t o t h e a X 2 02 0 0 & i B O X C o n n e c t i o n s WAN ConfigurationSounder /Beacon for i-BOX IC-ASB AX200 Expander Board Connections Breakglass Wiring AX200 Break glass Wiring AX200AX50 / AX100 Break glass wiring AX50/AX100Installation & User Guide Installation & User Guide 2 0 0 S o f t w a r e F t w a r e InstallationOperating Systems Installation & User Guide Installation & User Guide A r t i n g t h e a X 2 0 0 S o f t w a r e Language Selection Password ReminderWindows Classic or Graphic Style XP Screen C k u p & R e s t o r e Email Backup Settings Standard Query Language SQL Communication between the AX200 Software and Controller Database Integrity CheckPlug & Play Devices N t r o l l e r S t a t u s & C o n t r o l High Security Mode HSMDate and Time Door Unlock ModeOn & Offline Operation Performance Analyzer Force Download & Clear ControllerTransaction Screen Who’s In/Out List Photo Display Display FiltersInstallation & User Guide Test Wizard Save on ExitInstallation & User Guide Installation & User Guide Installation & User Guide Installation & User Guide R d h o l d e r Main SettingsCard Number Department Access GroupImprint Number EmploymentInstallation & User Guide Photo ID PhotoCapture Picture from Camera Add a PhotoTemplates Import Picture from FileAdd New Card Wizard Card Replacement Wizard Card Diagnostics Search Database Fields per Cardholder Main Settings TabCard 0 Function Print Current Card DetailsOther Info Employer Mode Settings Extended Door Open Time Ext’d Door Set High Security Mode Set Hi SecPersonal Info High Security Hi SecVehicle info C e s s P o i n t C o n f i g u r a t i o n Access Point SettingsAccess Identity Access Point NameDoor Comments Door Contact Settings Start-up Mode SettingsDoor Release Time PIN Settings Hardware Version Device ParametersDevice Group Device TypeSerial Number in Batch Access GroupsFirmware Version Batch NumberDevice Manager Creating a new access groupAutomatic IP Setup Installation & User Guide Device Status Indication Installation & User Guide Device Settings Test Connection Fire alarmSite Info S t e m S e t t i n g sTest Wizard Mail Unknown Format to Axxess ID Mail FacilitiesCompact Database DB MaintenanceFirmware Settings Rollback Hidden FunctionsInstallation & User Guide General Settings COM Port Settings Function SettingsLink Alive Retry Times Multiple/Single Card Format Select COM PortR m a t & S t a t i s t i c s Default Access LevelDefault Time Zone DefaultFacility Code Card Type InformationC u r i t y S e t t i n g s Card Format Analyzer & Format ConfigurationCard Matching Adding a New Authorisation Group Adding a New UserP o r t Cardholder Brief Log File Cardholder DetailsDossier System Summary Work SpellOperators EnvironmentalFormat Types PrintingDestination Door Panel Position Sensor V i r o n m e n t BOX Parameters Sensor SettingsAlarms Shunt alarm on delay BOX SettingsAccumulation Period PDU Power Distribution UnitDetails Power feed group Normal Power switched on, power sensed LED on solid Hardware Connection Details SensorIsolate PIR Installation & User Guide Dust Particle Sensor Mains Present Sensor U D a t a T r a n s f e r U n i t Connecting the DTUInstallation & User Guide Add a New Door using a DTU DTU Step by Step Adding Card Formats using a DTUDTU Operation DTU LED IndicatorsClear DTU M o v i n g t h e a X 2 0 0 P r o g r a mT i V i r u s Installation & User Guide Fingerprint Reader A d e r sConfiguring Verid+ Programming a New User Getting Started Quickly Proximity Readers Installation & User Guide Output Type AXM ReadersProximity Request to Exit