Ricoh PRIPORT VT2130 manual Installation Requirements, Machine Environment

Page 11

INSTALLATION REQUIREMENTS

1. Machine Environment

The installation location should be carefully chosen because environmental conditions greatly affect the performance of a machine.

I	ml	I	- Optimum		environmental			conditions			-
			●	Temperature:			10 – 30°c
							(50 - 86”F)
			●	Humidity:			20 – 90%			RH
			●	Ventilation:
				Well-ventilated and wide room.
			●	On	a	strong	and	level	base		(a
				sturdy		desk,	etc.).
			● The			machine	must		be	level
				within 5 mm (13/64”) both front
				to rear and le~ to right.

- Environments to avoid -

● Direct sunlight or strong light

● Locations directly exposed to the cool air from an air con- ditioner or reflected heat from a space heater. (Sudden tempe- rature changes low to high or vice versa may cause conden- sation within the machine.)

● Dusty areas.

Image 11

Contents Iiigom Page Introduction Table of Contents Machine Exterior Guide to ComponentsPage Machine Interior Ii= \Buttonmaster PlatetableCover OQ0000 Operation PanelPage Machine Environment Installation RequirementsPower Connection Access to MachineGeneral Cautions DO’S and DON’TSOperating Cautions Originalswith OriginalsYou can use the following type of originals Thickness Max MinIii MinMaxMin Avoid using the foliowing kindsPrinting Paper Print SizeOpen the paper OperationPreparation for Printing Lift the paper delivery side plates Turn on the main switchOpen the paper delivery table Select the image mode using Setting the OriginalsImage Mode keys Press the Print Start key Enter the number of prints required using the Number keysPrintina Press the Master Making keyRemove the paper from the paper feed table Slide in the paper delivery table Turn off the main switchRestoring Paper Feed and Paper Delivery Tabies Press Adjusting the Image PositionLeft Image Position key Shifting the image position backwardPress the Lower Paper Feed Table key Shifting the image to the rightPress the Lower Paper Feed Table Shifting the image to the leftChanging the Paper Size So bxSet the side pads Move the side pad levers to the right Printing on Thick or Thin PaperPrinting on thin paper Push down the feed roller pressure leverPlace Postcard Size Paper on Feed Printing on Postcard Size PaperPostcard size original Place the postcard sized paper onOpen the original table Various OriginalsPress the Speed key. To increase Changing the Printing Speed9o sheets/rein issd@d a@OrnatiCallY To Stop the Machine During a Printing Run Open the front door Changing the Drum Unit for Color PrintingPage Printing in Two Colors Press the Memory key Set using the Number keysSpecial Functions Group Printing from the Same OriginalSet the original face down on Press the Memory key again. The Memory returns to Memory93% Combine 2 OriainalsFor Example 81/2Press the Combine 2 Originals key Key. Check Various Run Lengths Using the Same MasterPress Master MakingOriginal Photo mode Line mode Photo Mode PrintingPress the Lower Paper Feed Table key Replenishing SuppliesLoadina Pa~er Supplying Ink Open the original table Master Roll ReplacementPage Clean the thermal head when 2 master rolls have been used MaintenanceThermal Head Cleaning Platen Cover / Exposure Glass Platen Cover / Exposure GlassRli Check the misfeed or malfunction location TroubleshootingIndicators Remove the jammed master and pressthe Resetkey. SeepageCopy When the Misfeed ~ Indicator LightsPrevent Original misfeeds To prevent paper feed jams Page Page Difficult to remov~ th’e paper from the paper feed section When the misfed ~a~er is underneath the drumPage When the Supply/Exchange fi Indicator Lights Incomplete master eject box No master eject box Installation When the master eject box is full, do the followingOther Indicators Light Poor Printina Original Operating Cautions ImiscellaneousPage Storing 735 x 607 x 569 mm 28.9 23.9x 22.4 Inches SPECIFICATION1Power Source Power Consumption Dimensions W XdxhSize Remarks Kg 220.4 lbOptional Equipment Consumables Name Priport Master 120V version