Ricoh PRIPORT VT2130 manual Maintenance, Thermal Head Cleaning

Page 43

MAINTENANCE

1. Thermal Head Cleaning

Clean the thermal head when 2 master rolls have been used.

1.Turn off the main switch.

2.Open the original table. (See page 38.)

3.Move the pressure release lever in the direction of the arrow. (See page 38.)

4.Loosen the screw knobs located on both sides of the feed roller.

5.Grip both ends of the feed roller and lift it straight up.

6.Clean the thermal head as follows.

I) Wipethe surfaceof the thermal head with a damp cloth.

2) Cleanthe surfaceof thermal head several times usingthe cleaner pen with cleaning

solution. (The cleaner pen is stored in the carton box as an accessory.)

3) Dry the surface of thermal head with a clean dry cloth.

I

I

I

Make sure to replace the cap of

I

 

Warning:

 

 

cleaner

after using it.

. Replace the felt of the cleaner pen if it be- comes ditty.

7.Install the feed roller by reversing the above procedure.

. Make sure to tighten the screw knobs on both sides of the feed roller.

40

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Iiigom Page Introduction Table of Contents Machine Exterior Guide to ComponentsPage Machine Interior Ii= \Cover PlatetableButtonmaster OQ0000 Operation PanelPage Machine Environment Installation RequirementsPower Connection Access to MachineOperating Cautions DO’S and DON’TSGeneral Cautions Originalswith OriginalsYou can use the following type of originals Thickness Max MinIii MinMaxMin Avoid using the foliowing kindsPrinting Paper Print SizePreparation for Printing OperationOpen the paper Open the paper delivery table Turn on the main switchLift the paper delivery side plates Image Mode keys Setting the OriginalsSelect the image mode using Press the Print Start key Enter the number of prints required using the Number keysPrintina Press the Master Making keyRestoring Paper Feed and Paper Delivery Tabies Slide in the paper delivery table Turn off the main switchRemove the paper from the paper feed table Press Adjusting the Image PositionLeft Image Position key Shifting the image position backwardPress the Lower Paper Feed Table key Shifting the image to the rightPress the Lower Paper Feed Table Shifting the image to the leftChanging the Paper Size So bxSet the side pads Move the side pad levers to the right Printing on Thick or Thin PaperPrinting on thin paper Push down the feed roller pressure leverPlace Postcard Size Paper on Feed Printing on Postcard Size PaperPostcard size original Place the postcard sized paper onOpen the original table Various Originals9o sheets/rein issd@d a@OrnatiCallY Changing the Printing SpeedPress the Speed key. To increase To Stop the Machine During a Printing Run Open the front door Changing the Drum Unit for Color PrintingPage Printing in Two Colors Press the Memory key Set using the Number keysSpecial Functions Group Printing from the Same OriginalSet the original face down on Press the Memory key again. The Memory returns to Memory93% Combine 2 OriainalsFor Example 81/2Press the Combine 2 Originals key Key. Check Various Run Lengths Using the Same MasterPress Master MakingOriginal Photo mode Line mode Photo Mode PrintingLoadina Pa~er Replenishing SuppliesPress the Lower Paper Feed Table key Supplying Ink Open the original table Master Roll ReplacementPage Thermal Head Cleaning MaintenanceClean the thermal head when 2 master rolls have been used Rli Platen Cover / Exposure GlassPlaten Cover / Exposure Glass Check the misfeed or malfunction location TroubleshootingIndicators Remove the jammed master and pressthe Resetkey. SeepagePrevent Original misfeeds When the Misfeed ~ Indicator LightsCopy To prevent paper feed jams Page Page Difficult to remov~ th’e paper from the paper feed section When the misfed ~a~er is underneath the drumPage When the Supply/Exchange fi Indicator Lights Incomplete master eject box No master eject box Installation When the master eject box is full, do the followingOther Indicators Light Poor Printina Original Operating Cautions ImiscellaneousPage Storing 735 x 607 x 569 mm 28.9 23.9x 22.4 Inches SPECIFICATION1Power Source Power Consumption Dimensions W XdxhSize Remarks Kg 220.4 lbOptional Equipment Consumables Name Priport Master 120V version
Top Page Image Contents