Ricoh PRIPORT VT2130 manual Troubleshooting, Indicators, Check the misfeed or malfunction location

Page 45

I	TROUBLESHOOTING	I
1. Indicators

[f a malfunction or a misfeed occurs within the machine, the following indicators will light.

-Check the misfeed or malfunction location.

Open the top unit cover, remove original and reset. (See page 43.)

Remove the jammed paper and press the Reset key. (See page 44.)

Remove the jammed master and pressthe Resetkey. (Seepage 45.)

Open the master eject unit and remove any jammed paper, then press the Reset key. If the paper is stuck to the drum, pull out the drum unit until the drum unit hits the drum stopper, and remove the jammed paper from the drum. (See page 46.)

1.If the paper is stuck to the drum, pull out the drum unit until the drum unit hits the drum stopper, and remove the jammed paper from the drum.

2.If the jam is in the paper feed section, the jammed paper may be cleared at either the paper entrance or the paper exit side.

(See page 47.)

Open the master eject unit and remove the jammed master. Press Reset key. If the jammed master is stuck to the drum, pull out the drum unit and remove the misfed master. (See page 48.)

Open the master eject unit and remove the jammed paper. Press Reset key. (See page 48.)

Check that the original is correctly placed and that the counter is set for the required number of copies. (See page 49.)

Load paper. (See page 49.)

Load new master roll. (See page 49.)

Load new ink cartridge. (See page 50.)

1.Remove the used masters inside the master eject box.

2.Make sure the master eject box is replaced correctly. (See page 50.)

Check the setting of the original table, the front cover, the master eject

unit,the drum, the paper feed table, and the top unit. (Seepage 51.) Color drum is installed.(See page 51.)

Set the key counter. (See page 51.)

If a service code (EO1– E08) is displayed in the counter, please contact your service representative.

42

Image 45

Contents Iiigom Page Introduction Table of Contents Machine Exterior Guide to ComponentsPage Machine Interior Ii= \Platetable CoverButtonmaster OQ0000 Operation PanelPage Machine Environment Installation RequirementsPower Connection Access to MachineDO’S and DON’TS Operating CautionsGeneral Cautions You can use the following type of originals Thickness OriginalsMax Min OriginalswithIii Printing Paper Avoid using the foliowing kindsPrint Size MinMaxMinOperation Preparation for PrintingOpen the paper Turn on the main switch Open the paper delivery tableLift the paper delivery side plates Setting the Originals Image Mode keysSelect the image mode using Printina Enter the number of prints required using the Number keysPress the Master Making key Press the Print Start keySlide in the paper delivery table Turn off the main switch Restoring Paper Feed and Paper Delivery TabiesRemove the paper from the paper feed table Left Image Position key Adjusting the Image PositionShifting the image position backward PressPress the Lower Paper Feed Table Shifting the image to the rightShifting the image to the left Press the Lower Paper Feed Table keyChanging the Paper Size So bxPrinting on thin paper Printing on Thick or Thin PaperPush down the feed roller pressure lever Set the side pads Move the side pad levers to the rightPostcard size original Printing on Postcard Size PaperPlace the postcard sized paper on Place Postcard Size Paper on FeedOpen the original table Various OriginalsChanging the Printing Speed 9o sheets/rein issd@d a@OrnatiCallYPress the Speed key. To increase To Stop the Machine During a Printing Run Open the front door Changing the Drum Unit for Color PrintingPage Printing in Two Colors Special Functions Set using the Number keysGroup Printing from the Same Original Press the Memory keySet the original face down on Press the Memory key again. The Memory returns to MemoryFor Example Combine 2 Oriainals81/2 93%Press the Combine 2 Originals key Press Various Run Lengths Using the Same MasterMaster Making Key. CheckOriginal Photo mode Line mode Photo Mode PrintingReplenishing Supplies Loadina Pa~erPress the Lower Paper Feed Table key Supplying Ink Open the original table Master Roll ReplacementPage Maintenance Thermal Head CleaningClean the thermal head when 2 master rolls have been used Platen Cover / Exposure Glass RliPlaten Cover / Exposure Glass Indicators TroubleshootingRemove the jammed master and pressthe Resetkey. Seepage Check the misfeed or malfunction locationWhen the Misfeed ~ Indicator Lights Prevent Original misfeedsCopy To prevent paper feed jams Page Page Difficult to remov~ th’e paper from the paper feed section When the misfed ~a~er is underneath the drumPage When the Supply/Exchange fi Indicator Lights Incomplete master eject box No master eject box Installation When the master eject box is full, do the followingOther Indicators Light Poor Printina Original Operating Cautions ImiscellaneousPage Power Source SPECIFICATION1Power Consumption Dimensions W Xdxh Storing 735 x 607 x 569 mm 28.9 23.9x 22.4 InchesOptional Equipment Consumables Name Priport Master Kg 220.4 lb120V version Size Remarks