Ricoh PRIPORT VT2130 manual

Page 58

10.When making duplex prints, misdetection of paper wrapping may occur because the paper delivery sensor detects the black area at the leading edge of the back side. Keep more than 10mm/O.4° blank area at the leading edge of the back side of the printing paper.

11.Do not use the thermal head cleaner for anything but cleaning the ther- mal head. Also, be Sure to read ttle cautions about the thermal head cleaner, and be careful as this cleaner is an alcohol.

Take note of the following regarding the cleaner:

●Do not take internally.

●Do not breathe it.

●Keep out of the reach of children.

●If it comes in contact with skin, wash well with water.

●Keep away from eyes. If it comes in contact with your eyes, wash well. If irritation occurs, contact your doctor.

●Never place it whet’e it will be exposed to heat.

12.When feeding 51/2’’x8l/2° paper in the sideways direction, the prints may

not stack correctly on the paper delivery table. In this case, push up the wing guide release lever.

13.Perform a test print using the Proof key as the first few prints may be light.

14.When the machine is m and the power source is less than 90% of the specified amount, printing quality will decrease. Therefore, make sure the mains supply is at least 90% of the required amount.

15.Such paper as postcards do not absorb ink well. Therefore, offset im- ages may appear on the rear side of following prints. Solid image originals will make offset image prints.

16.AS various kinds and qualities of paper exist, Some paper may be wrapped around the drum and/or cause jams.

55

Image 58

Contents Iiigom Page Introduction Table of Contents Guide to Components Machine ExteriorPage Ii= \ Machine InteriorCover PlatetableButtonmaster Operation Panel OQ0000Page Installation Requirements Machine EnvironmentAccess to Machine Power ConnectionOperating Cautions DO’S and DON’TSGeneral Cautions Max Min OriginalsYou can use the following type of originals Thickness OriginalswithIii Print Size Avoid using the foliowing kindsPrinting Paper MinMaxMinPreparation for Printing OperationOpen the paper Open the paper delivery table Turn on the main switchLift the paper delivery side plates Image Mode keys Setting the OriginalsSelect the image mode using Press the Master Making key Enter the number of prints required using the Number keysPrintina Press the Print Start keyRestoring Paper Feed and Paper Delivery Tabies Slide in the paper delivery table Turn off the main switchRemove the paper from the paper feed table Shifting the image position backward Adjusting the Image PositionLeft Image Position key PressShifting the image to the left Shifting the image to the rightPress the Lower Paper Feed Table Press the Lower Paper Feed Table keySo bx Changing the Paper SizePush down the feed roller pressure lever Printing on Thick or Thin PaperPrinting on thin paper Set the side pads Move the side pad levers to the rightPlace the postcard sized paper on Printing on Postcard Size PaperPostcard size original Place Postcard Size Paper on FeedVarious Originals Open the original table9o sheets/rein issd@d a@OrnatiCallY Changing the Printing SpeedPress the Speed key. To increase To Stop the Machine During a Printing Run Changing the Drum Unit for Color Printing Open the front doorPage Printing in Two Colors Group Printing from the Same Original Set using the Number keysSpecial Functions Press the Memory keyPress the Memory key again. The Memory returns to Memory Set the original face down on81/2 Combine 2 OriainalsFor Example 93%Press the Combine 2 Originals key Master Making Various Run Lengths Using the Same MasterPress Key. CheckPhoto Mode Printing Original Photo mode Line modeLoadina Pa~er Replenishing SuppliesPress the Lower Paper Feed Table key Supplying Ink Master Roll Replacement Open the original tablePage Thermal Head Cleaning MaintenanceClean the thermal head when 2 master rolls have been used Rli Platen Cover / Exposure GlassPlaten Cover / Exposure Glass Remove the jammed master and pressthe Resetkey. Seepage TroubleshootingIndicators Check the misfeed or malfunction locationPrevent Original misfeeds When the Misfeed ~ Indicator LightsCopy To prevent paper feed jams Page Page When the misfed ~a~er is underneath the drum Difficult to remov~ th’e paper from the paper feed sectionPage When the Supply/Exchange fi Indicator Lights When the master eject box is full, do the following Incomplete master eject box No master eject box InstallationOther Indicators Light Poor Printina Original Imiscellaneous Operating CautionsPage Power Consumption Dimensions W Xdxh SPECIFICATION1Power Source Storing 735 x 607 x 569 mm 28.9 23.9x 22.4 Inches120V version Kg 220.4 lbOptional Equipment Consumables Name Priport Master Size Remarks