Printing quality problems
If the inside of the machine is dirty or paper has been loaded improperly, you may notice a reduction in print quality. See the table below to clear the problem.
Condition | Suggested solutions |
|
|
Light or faded | If a vertical white streak or faded area appears on |
the page: |
AaBbCc | • The toner supply is low. You may be able to | |
temporarily extend the toner cartridge life. See | ||
AaBbCc | page 8.3. If this does not improve the print | |
AaBbCc | quality, install a new toner cartridge. | |
• The paper may not meet paper specifications; for | ||
AaBbCc | ||
example, the paper is too moist or too rough. See | ||
AaBbCc | page 3.2. | |
| • If the entire page is light, the print resolution | |
| setting is too low or the toner save mode is on. | |
| Adjust the print resolution and turn the toner save | |
| mode off. See the Software Section and | |
| page 2.6, respectively. |
•A combination of faded or smeared defects may indicate that the toner cartridge needs cleaning. See page 8.2.
•The surface of the LSU part inside the machine may be dirty. Clean the LSU. See page 8.2.
Toner specks | • The paper may not meet specifications; for | |
AaBbCc | example, the paper is too moist or too rough. See | |
page 3.2. | ||
AaBbCc | • The transfer roller may be dirty. Clean the inside | |
AaBbCc | of your machine. See page 8.1. | |
• The paper path may need cleaning. See page 8.2. | ||
AaBbCc |
| |
AaBbCc |
| |
Dropouts | If faded areas, generally rounded, occur randomly | |
| on the page: | |
AaBbCc | • A single sheet of paper may be defective. Try | |
AaBbCc | reprinting the job. | |
• The moisture content of the paper is uneven or | ||
AaBbCc | ||
the paper has moist spots on its surface. Try a | ||
AaBbCc | different brand of paper. See page 3.2. | |
AaBbCc | • The paper lot is bad. The manufacturing | |
| processes can cause some areas to reject toner. | |
| Try a different kind or brand of paper. |
•If these steps do not correct the problem, contact a service representative.
Condition | Suggested solutions |
|
|
Vertical lines | If black vertical streaks appear on the page: |
AaBbCc | • The drum inside the toner cartridge has probably | |
been scratched. Remove the toner cartridge and | ||
AaBbCc | install a new one. See page 8.4. | |
AaBbCc |
| |
AaBbCc | If white vertical streaks appear on the page: | |
AaBbCc | • The surface of the LSU part inside the machine | |
may be dirty. Clean the LSU (see page 8.2). | ||
|
Gray background | If the amount of background shading becomes | ||
|
|
| unacceptable: |
|
|
| |
AaBbCc | • Change to a lighter weight paper. See page 3.2. | |
AaBbCc | • Check the machine’s environment: very dry (low | |
AaBbCc | humidity) or high humidity (higher than 80% RH) | |
conditions can increase the amount of background | ||
AaBbCc | ||
shading. | ||
AaBbCc | • Remove the old toner cartridge and install a new | |
| one. See page 8.4. | |
Toner smear | • Clean the inside of the machine. See page 8.1. | |
| • Check the paper type and quality. See page 3.2. | |
| • Remove the toner cartridge and install a new one. | |
| See page 8.4. |
Vertical repetitive If marks repeatedly appear on the printed side of | ||
defects | the page at even intervals: | |
AaBbCc | • The toner cartridge may be damaged. If a | |
repetitive mark occurs on the page, print a | ||
AaBbCc | cleaning sheet several times to clean the toner | |
AaBbCc | cartridge; see page 8.2. After the printout, if you | |
still have the same problems, remove the toner | ||
AaBbCc | ||
cartridge and install a new one. See page 8.4. | ||
AaBbCc | • Parts of the machine may have toner on them. If | |
| the defects occur on the back of the page, the | |
| problem will likely correct itself after a few more | |
| pages. | |
•The fusing assembly may be damaged. Contact a service representative.
•If you use inferior quality paper; see page 8.2.
9.7