Initial SET UP/INFORMATION | Mitsubishi Electronics DX-TL950E

<INITIAL SET UP/INFORMATION> (continued)

♦SEQUENTIAL PLAY

It is possible to make archive of the video recorded with this unit to an analogue video recorder, etc., while playing back the video of each camera in order using the single screen display. During single screen sequential playback, the SPLIT/SEQUENCE button will light. In addition, the playback order/time of each camera will be the order of the recorded video.

<HDD	SETTINGS>	ON
HDD	REPEAT REC MAIN	ON
HDD	REPEAT REC SUB	OFF
HDD	REPEAT PLAY	OFF
IM-CHECK PLAY		OFF
>>SEQUENTIAL PLAY		OFF

Setting ( default : “OFF” )

“ON” : Plays back the video in the single screen se- quential mode.

“OFF” : Does not play back the video in the single screen sequential mode.

Playback is performed during camera sequential play at an interval of 25P. To change the playback interval, press

the PLAY button (or the REV. PLAY button)( see “Changing playback intervals, pages 65,66).

1.Press the SET UP button } <SETTINGS> } <INITIAL SET UP/INFORMATION> } Select “SEQUENTIAL PLAY” in the <HDD SETTINGS> screen. Display the desired setting and confirm.

2.Turn the SHUTTLE ring counterclockwise or press the SET UP button.

3.Press the PLAY button.

4.Press one of the camera number buttons with recorded video.

•Single screen sequential playback starts.

When performing camera sequential playback for video with long recording intervals, the video of the largest camera number selected for recording will be played back the longest.

Only the camera number (title) of the pressed cam- era number button is displayed. Other camera number (titles) will not be displayed. If display is not necessary,

select “NONE” in the <CAMERA DISPLAY> ( see page 32).

■AUDIO RECORDING

This unit can simultaneously record audio along with the video. When recording audio, the continuous recording time becomes shorter than when recording only video.

<INITIAL SET UP/INFORMATION> HDD SETTINGS

>>AUDIO RECORDINGOFF REAR TERMINAL SETTINGS COMMUNICATION PORT SETTINGS INFORMATION/SERVICE PASSWORD

LANGUAGE SELECTION

Setting ( default : “OFF” )

“ON” : Records video and audio.

“ALARM” : During alarm recording or emergency re- cording, records video and audio.

“OFF” : Does not record audio.

1.Press the SET UP button } <SETTINGS> } Select “AUDIO RECORDING” in the <INITIAL SET UP/INFORMATION> screen. Display the desired setting and confirm.

2.Turn the SHUTTLE ring counterclockwise or press the SET UP button.

When setting “AUDIO RECORDING” to “ON”, a speaker display ( ) appears to the right of recordable time display in the <RECORD SETTING> and

<RECORD SETTING A> ~ <RECORD SETTING D> screens.

<RECORD SETTING>			>>ALARM CH
NO	PPS	GRADE	A-PPS	A-GRADE
1	2.5P	STD	2.5P	STD
2	2.5P	STD	2.5P	STD
3	2.5P	STD	2.5P	STD
4	2.5P	STD	2.5P	STD
5	2.5P	STD	2.5P	STD
6	2.5P	STD	2.5P	STD
7	2.5P	STD	2.5P	STD
8	2.5P	STD	2.5P	STD
9	2.5P	STD	2.5P	STD
<ESTD REC>			D H	M

Even when setting “AUDIO RECORDING” to “ON”, audio cannot be recorded for the following settings.

•Audio recording cannot be performed when “PPS” of “RECORD SETTING” are all set to smaller than “0.333P” when setting normal recording. In this case,

( X ) appears to the right of recordable time display.

•When the camera selection during alarm recording is as follows :

“ALARM CH” : “A-PPS” of all cameras set for alarm recording are set to smaller than “0.333P”.

“ALARM PLUS”, “ALARM25” : “PPS” and “A-PPS” of all cameras set for normal recording and alarm record- ing are set to smaller than “0.333P”.

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

•••••••••••••