Mitsubishi Electronics DX-TL950E Reset to Factory Settings Menu screen settings are reset

1.Press the SET UP button } <SETTINGS> } <INITIAL SET UP/INFORMATION> } Select “WARNING LOG LIST” in the <INFORMATION/SERVICE> (1/2) screen. Turn the SHUTTLE ring clockwise.

•The <WARNING LOG LIST> screen appears.

•The WARNING LOG LIST can display up to 1000 items. When the number of items exceed this limit, the latest 1000 items are displayed.

• button/turn JOG dial counterclockwise : Selection moves

to the next number.

• button/turn JOG dial clockwise : Selection moves to the previous number.

• button : Displays the page with date prior to the date of the currently opened page.

• button : Displays the page with date newer than the date of the currently opened page.

When a failure occurs while the <WARNING LOG LIST> is being displayed, exit the screen and display the screen again. A new item will be added to the list.

Failures displayed in the WARNING LOG LIST

( see pages 87,88).

<WARNING LOG		LIST>	WARNING
NO	DATE	TIME
>>0001	02-02-04	10:00:00	ALM ON

<The “WARNING” are displayed in red.>

•“P-LOSS” : Power failure.

•“SYS RST” : Reset button was pressed and the unit was reset.

<The “WARNING” are displayed in green.>

•“ALM OFF” : The ALARM INTERRUPT button was pressed and the unit was put on interruption.

•“ALM ON” : The ALARM INTERRUPT button was pressed and the alarm interrupt was cancelled.

•“REC ON” : The record was started.

•“REC OFF” : The record was stopped.

•“PS-OFF” : PASSWORD LOCK was unlocked.

•“PS-1” : The PASSWORD level 1 was locked.

•“PS-2” : The PASSWORD level 2 was locked.

•“PS-3” : The PASSWORD level 3 was locked.

•“PS-4” : The PASSWORD level 4 was locked.

•“PS-E” : The SIMPLE LOCK was locked.

When recording is started, “REC ON” is registered in <WARNING LOG LIST>. However, “REC ON” will not be registered when recording is resumed after power is restored.

For power outages that occur while timer recording is standing by, “P-LOSS” that indicates a power outage is not displayed. In addition, power outages that overlap with timer recording start times and those where power is restored after the recording end time are also not recorded.

2.Turn the SHUTTLE ring counterclockwise or press the SET UP button.

♦RESET TO FACTORY SETTINGS Menu screen settings are reset.

1.Press the SET UP button } <SETTINGS> } <INITIAL SET UP/INFORMATION> } Select “RESET TO FACTORY SETTINGS” in the <INFORMATION/SERVICE> (1/2) screen. Turn the SHUTTLE ring clockwise.

•The <RESET TO FACTORY SETTINGS> screen appears.

•When not resetting menu screen settings, turn the SHUTTLE ring counterclockwise.

<RESET TO FACTORY SETTINGS>

>>EXECUTE

SHUTTLE>>:EXECUTE,<<:CANCEL

2.Turn the SHUTTLE ring clockwise.

•The menu screen settings are reset.

The <TIMER PROGRAM> setting is not initialized.

When menu initialization is performed when a setting change has been made for any one item of “IP ADDRESS” , “SUB NET MASK” , “GATEWAY” , “SERVICE PORT SETTING” on the <ETHERNET> screen or “IP ADDRESS”, “TARGET” or “OWN” of the <ALARM NOTIFICATION SETTING> settings, restart is performed after the power has been cut.

3.Turn the SHUTTLE ring counterclockwise or press the SET UP button.

♦DATA CLEAR

For deleting data in MAIN HDD, SUB HDD or CFC (Com- pact Flash Card).

“SUB HDD DATA CLEAR” is appeared when the “HDD SETTING” is selected on “PARTITION” of the <INITIALIZATION> screen.

Performing “MAIN HDD DATA CLEAR” while in “MIRRORING” mode deletes all data.

1.Press the SET UP button } <SETTINGS> } <INITIAL SET UP/INFORMATION> } Select the desired item to clear in the <INFORMATION/SERVICE> (1/2) screen. Turn the SHUTTLE ring clockwise.

•“PUSH WARNING RESET KEY FOR 1 SECOND TO CLEAR” appears on the bottom of the screen.

•To cancel the deletion, turn the SHUTTLE ring counter- clockwise.

<MAIN HDD DATA CLEAR>

PUSH WARNING RESET KEY

FOR 1 SECOND TO CLEAR

ENGLISH

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Operations

55