Operating your AV8
INTRODUCTION
For information display we recommend you use the OSD on your TV/screen whenever possible. However all key information is also duplicated one line at a time on the front panel display of the AV8.
USING THE CONTROLS
SWITCHING ON
Press the power button in. Between one and five seconds later, the power LED will then come on (first as yellow), the front panel display window shows ‘ARCAM’, followed by ‘initialising’. This is followed by the initial volume setting and the name of the input selected. After initialisation is complete, the power LED changes colour to green.
Please wait until the unit has finished initialising before operating the AV8. It is recommended that if the unit is switched off, you should wait at least 10 seconds before switching the unit back on.
STANDBY
The AV8 has a standby mode which can be entered by pressing STANDBY on the remote control. When in standby mode the display is blank and the power LED glows red.
When not being used, the AV8 may be left in standby mode, as power consumption is low. If you are not using your AV8 for several days we recommend you switch the unit completely off at the front panel.
TO SWITCH ON FROM STANDBY
Press one of the source buttons on the front panel or on the remote control, or use the standby button on the remote control.
FRONT PANEL DISPLAY
The AV8 is ready for use after about four seconds.This display window shows the processing mode and initial volume setting.
Output channels in digital processing modes are indicated in the format: ‘3/2.1’, where ‘3’ refers to the front channels, ‘2’ to the rear channels, and ‘.1’ to the subwoofer channel. Some variants of this format are described below.
| To n e |
V o l : + 8 | A n . P L I I |
| M o v i e |
Recorded | Front | Surround | Sub- | Comment |
format | speakers | speakers | woofer |
|
|
|
|
|
|
3/2/1 | 3 | 2 | Yes | Full 5.1 sound |
|
|
|
|
|
3/2/0 | 3 | 2 | No | |
|
|
|
|
|
3/0/0 | 3 | No | No | |
|
|
|
|
|
2/0/0 | 2 | No | No | Stereo (Dolby digital or |
|
|
|
| DTS encoded) |
|
|
|
|
|
SELECTING A SOURCE |
|
| ||
To select a particular source, press the corresponding button on the front panel or on the remote control. There are nine inputs available: DVD, Sat, AV, VCR, Phono/Aux, CD, Tuner, Tape and
On selecting a source, the AV8 will normally select an active digital input in preference to an analogue input. If you want to override the digital input and select the analogue input, press and hold the source button for at least two seconds.
The processing mode and Stereo Direct functions are remembered and recalled for each input. The digital input and high quality video input associated with each source may be customised in the setup procedure.
The
TAPE OPERATION
The AV8 has a fully independent tape loop.This can be configured to record the source you are listening to, or to record any other input using the ‘Record to Tape’ option in ‘Main Menu Screen 2’.
Pressing the TAPE button will select audio from the tape input.
If the ‘Record to Tape’ option is set to Source (its default setting), the tape LED will illuminate as well as the previously selected input.
If the ‘Record to Tape’ option is set to a specific input, the tape LED will illuminate as well as the input selected in the ‘Record to Tape’ menu item.
This indicates the tape loop is active and displays the source that will be recorded.
For example, if ‘Record toTape’ is set to Source and you want to record the CD input:
Select the CD input then put your recorder into record pause so that it will monitor its input.
Press the TAPE button – you can now listen to the sound actually being recorded by your tape deck from the CD player.
If you select a different source from CD, the recording will change to this source.
If you want to record from CD while listening to the Tuner input:
Call up the ‘Main Menu Screen 2’ and set ‘Record to Tape’ to CD.
Put your recorder into record pause so that it monitors its input then press the TAPE button.You can now start the recording and listen to the sound actually being recorded by your tape deck from the CD player.
Once the recording is running press the TUNER button to listen to the Tuner, the recording of the CD will continue.
You can check the progress of the recording at any time by pressing the TAPE button again.
VCR OPERATION
The AV8 has a fully independent VCR loop for audio and video (Composite and
Pressing the VCR button selects audio and video from the VCR input.
If the ‘Record to VCR’ option is set to Source (its default setting), the VCR LED illuminates as well as the previously selected input.
If the ‘Record to VCR’ option is set to a specific input, the VCR LED illuminates as well as the input selected in the VCR menu.
This indicates the VCR loop is active and displays the source that will be recorded.
English