JVC HM-DR10000EU Quest Ions and Answers, Ä remain lit on the display panel. Is there Problem?

Page 75

QUESTIONSANDANSWERS

EN75

PLAYBACK

TIMER RECORDING

Q. What happens if the end of the tape is reached during playback or search?

A. The tape is automatically rewound to the beginning.

Q. Can the video recorder indefinitely remain in the still mode?

A.No. It stops automatically after 5 minutes to protect the heads.

Q.When returning from multi-speed search to normal playback, the picture is disturbed. Should I be concerned about this?

A.No, it is normal.

Q.Sometimes, during Index Search, the video recorder can’t find the programme I want to see. Why not?

A.There may be index codes too close together.

Q. "" and "ä" remain lit on the display panel. Is there

aproblem?

A.No. This is a normal condition for a timer recording in progress.

Q.Can I programme the timer while I’m watching a tape or a TV broadcast?

A.You won’t see the picture as it is replaced by the on- screen menu, but the audio from the programme or tape you’re viewing can be heard.

Q.Is it possible to timer-record a TV programme broadcast in 2000?

A.Yes, it is possible.

RECORDING

Q. When I pause and then resume a recording, the end of the recording before the pause is overlapped by the beginning of the continuation of recording. Why does this happen?

A. This is normal. It reduces distortion at the pause and resume points.

Q. Can the video recorder indefinitely remain in the Record-Pause mode?

A. No. The video recorder goes to its Stop mode automatically after 5 minutes to protect the heads.

Q. What happens if the tape runs out during recording? A. The video recorder automatically rewinds it to the

beginning.

ATTENTION

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 75

Contents HM-DR10000EU MTP PAL Safety PrecautionsDo not place the recorder Symptoms of dirty video headsEarly symptom Late symptom Block noise Still imageMains Check ContentsBasic Connection Situate RecorderBack of Recorder Video ConnectionConnect Recorder to TV Connect Recorder to MainsAuto Set Up If you are referring to the front display panelIf you are referring to the on-screen display Language Code Link and press OK Preset DownloadPress %Þ to select CH - and press OK or # Press %Þ to move Highlight bar pointer toJust Clock on If both auto channel set and auto clock set have failedLanguage for the on-screen display Just ClockScreen LanguageOn-Screen Displays ENABLE/DISABLE ON-SCREEN DisplayReturn to Normal Screen Power Save ModeSelect Power Save ModeAccess Main Menu Screen Access Mode SET ScreenLink Functions Press %Þ to move the highlight bar pointer to Colour System SetReturn to Normal Screen About Ntsc PlaybackStart Playback Basic PlaybackLoad a Cassette PointPress Pause Playback FeaturesPause During Playback Still Picture/Frame-By-Frame PlaybackManually Adjust TrackingActivate HIGH-SPEED Search Override Automatic TrackingIndex Search Activate Index SearchDigital 3R S-VHS/VHS Mode Only Digital TBC/NR S-VHS/VHS Mode OnlyRepeat Playback Soundtrack Selection S-VHS/VHS Mode Soundtrack Selection D-VHS ModeDuring Playback Basic Recording Recording Mode Compatibility Of Cassettes And Recording ModeStart Recording Recording FeaturesEngage ITR Mode Select Channel to WatchElapsed Recording Time Indication Reset CounterSET Counter Display Display Remaining TimeVHS Super VHS And VHS Audio Rec Mode Setting D-VHS Mode Only Receiving Stereo And Bilingual ProgrammesTo Record Stereo And Bilingual Programmes A2 S.T., then press OK or Select B.E.S.T. ModeS.T. Picture PreparationRecording PlaybackOr press Record on the recorder Timer Programming VHS mode Press STD/LS3 VHS or VHS modeSatellite Tuner Users Express Timer Programming Start TimeTime Engage RECORDER’S SET VPS/PDC ModeTimer Mode SET Tape SpeedTime you press Check, Cancel And Replace ProgrammesPress ä or äTIMER Press Again to check More information. EachThen press OK or #to select Auto SP→LP Timer S-VHS/VHS Mode OnlyFor Example SET, then press OK or #OK or #to select either Auto TimerHighlight bar pointer to Mode SET, then press Auto TIMER, then pressBefore performing the following steps Prog REC ModeAutomatic Satellite Programme Recording SET Tape SpeedChoose a Programme Access Title ScreenNavigation Load a Recorded CassetteTurn OFF Navigation Access Main Menu ScreenAccess Video Navigation Screen Check MemoryAccess Video Title EditingEdit Tape Title Entering Character Enter CharacterEnter Character Select CategorySelect Tape Title Delete Tape DataDelete Tape Data To delete, then press Delete ProgrammeData Delete Programme DataSorting By Tape Number Access Sorting ScreenSorting By Category Sorting By DateCode Remote Control FunctionsSET Remote Control Remote A/B Code SwitchingOperate TV TV Multi-brand Remote ControlTV/VCR, TV +/- Volume SET TV Brand CodeTV Prog +/-,NUMBER keys Satellite Tuner Multi-Brand Remote ControlSET Satellite Tuner Brand CodeSelect Picture Access Mode SETControl SET Mode Preparation For EditingEdit From Camcorder Recorder DV Sound SettingIf the camcorder has an S-VIDEO output connector If the camcorder has a DV OUT connector RecorderEdit To Or From Another Video Recorder Recorder Player AV2 Select Setting AV1 Select SettingSynchro Edit connector Lanc Cable not provided Synchro EditingRepeat steps 5 7 as necessary SET Jlip ID Number Access Initial SET ScreenAccess Jlip ID NO. SET Screen Terminal Jlip Joint Level Interface Protocol ConnectorBack of TV Connection To Satellite TunerSimple Connections Satellite Tuner UnitConnectors Scart Perfect ConnectionsDecoder Cable Basic ConnectionsSET Tuner Connecting Using a DecoderSelect Input Mode Connect DecoderRear View Connecting Using a Stereo SystemAccess Auto CH SET Tuner SetAuto Channel Set View Confirmation Screen Perform Auto Channel SETInput Channel Access Main MenuAccess Confirmation Screen Select BandPress %Þ @ #until the item you want to move begins When Receiving a Scrambled BroadcastDelete a Channel Change Station Channel PositionEnter NEW Character TV Station And ID List Select Channel to FINE-TUNE Access Manual Channel SET ScreenPerform Tuning Fine-Tuning Channels Already StoredGuide Program Number Set Showview SetupNumber Enter Receiving Channel Position NumberTurn the Recorder on Access Initial SET ScreenAccess Clock SET Screen Clock SetChannel position to the number representing Default setting is OFF. Set as desired by pressingRecorder is preset to receive clock setting SET Just ClockNo power is applied to the recorder Remote control wont functionPress Play to turn the indicator off Check the cassette Timer Recording Error Code Quest Ions and Answers Ä remain lit on the display panel. Is there Problem?Index Pull the front panel to access covered buttons/connectorsInside View of Front Panel Rear View If the counter exceeds -20 hours -200000, Display does not show the -2 of -200000. In thisCase, confirm the counter on the TV screen 80 EN Remote Control LCD PAL-type colour signal and Ccir Recording specificationChange Station Channel Position Express Timer ProgrammingManual Channel Setting Manual Tracking Automatic Satellite Programme RecordingEx. Deutschland is selected Ex. Francais is selected for BelgiumInternational Telephone Language Code