JVC HM-DR10000EU Automatic Satellite Programme Recording, SET Tape Speed, Prog REC Mode

Page 37

EN37

Automatic

Satellite

Programme

Recording

STD/LS3 (SP/LP)

REC LINK indicator

ATTENTION

●Be sure not to turn on the satellite tuner before the programme is executed; otherwise, the recorder will start recording when the satellite tuner's power is turned on.

●If you have connected another appliance other than a satellite tuner to the AV2 IN/DECODER connector, be sure not to engage the Auto Satellite Prog Rec mode; otherwise, the recorder will start recording when the connected appliance's power is turned on.

●Auto Satellite Prog recording and timer-recording cannot be done at the same time.

This facility allows you record automatically a satellite programme which is timer-programmed on your external satellite tuner. Connect a satellite tuner to the recorder's AV2 IN/DECODER connector (☞ pg. 57, 58) and programme the timer on the satellite tuner; the recorder starts recording when the signals input from the satellite tuner to the AV2 IN/DECODER connector, and when there is no input signals the recorder stops recording and the power shuts off.

Before performing the following steps:

●Make sure the satellite tuner is connected to the recorder's AV2 IN/DECODER connector. (☞ pg. 57, 58)

●Programme the timer on the satellite tuner.

●Insert a cassette with the safety tab in place.

●Set the appropriate recording mode (D-VHS, S-VHS or VHS) (☞ pg. 22, 23).

 

1

 

SELECT AV2 SELECT MODE

 

Set "AV2 SELECT" to "AV2" (☞ pg. 54).

 

 

 

 

 

● When you select "SAT", refer to "IMPORTANT" on

 

 

page 57.

 

 

 

 

 

 

2

 

SET TAPE SPEED

 

D-VHS mode:

 

 

 

Press STD/LS3 (

) to set the tape speed.

 

S-VHS or VHS mode:

 

 

 

Press SP/LP (

) to set the tape speed.

 

 

 

 

 

 

 

ENGAGE AUTO SATELLITE

 

3

 

PROG REC MODE

 

Press and hold REC LINK on the recorder for about 2

 

 

seconds. The REC LINK indicator lights up and the

 

 

recorder turns off automatically.

 

 

 

● To disengage the Auto Satellite Prog Rec mode, press

 

 

 

REC LINK. The REC LINK indicator goes off.

 

 

 

● If the recorder's power is off, it is not possible to

 

 

 

engage the Auto Satellite Prog Rec mode.

NOTES:

●Auto Satellite Prog recording is possible with the AV2 IN/DECODER connector only. (☞ pg. 57, 58)

●For timer programming of the satellite tuner, refer to the instruction manual of the satellite tuner.

●Auto Satellite Prog recording is not possible if your satellite tuner does not have a timer.

●The REC LINK indicator blinks while Auto Satellite Prog recording is in progress.

●Pressing the recorder's button while Auto Satellite Prog recording is in progress turns off the recorder's power and disengage the Auto Satellite Prog Rec mode.

●If there are more than one satellite programme you wish to record with Auto Satellite Prog Recording, it is not possible to set the different tape speed per each; the tape speed selected in step 2 will be applicable to all the programmes for Auto Satellite Prog recording.

●The B.E.S.T. system (☞ pg. 28) does not work while Auto Satellite Prog recording is in progress.

●Just Clock (☞ pg. 70) does not work when the Auto Satellite Prog Rec mode is engaged.

●Depending on the type of satellite tuner, the recorder may not record a slight portion of the beginning of the programme or may record slightly longer than the actual length of the programme.

●If you engage the Auto Satellite Prog Recording mode when the satellite tuner's power is on, the recorder will not start Auto Satellite Prog recording even though the REC LINK indicator blinks. When the satellite tuner shuts off once and is turned back on again, the recorder starts recording.

●When the Auto Satellite Prog Rec mode is engaged or the recorder's power is turned off after Auto Satellite Prog recording is finished, the recorder will not enter the Timer mode even though "AUTO TIMER" is set to "ON".

●You can also record a programme from your cable system in the same way if the system has a timer.

●When you press and hold the recorder's REC LINK button to engage the Auto Satellite Prog Rec mode, if the REC LINK indicator does not light but instead blinks quickly even though your satellite tuner's power is off, Auto Satellite Prog Recording will not work properly with that satellite tuner*.

If this is the case, perform "Express Timer Programming" (☞ pg. 32) to timer-record a satellite programme.

* Some satellite tuners output signals even if the power is off. Auto Satellite Prog Recording is not possible with those satellite tuners.

Page 36 Page 38
Image 37
Page 36 Page 38
Contents HM-DR10000EU MTP PAL Safety PrecautionsEarly symptom Symptoms of dirty video headsLate symptom Block noise Still image Do not place the recorderBasic Connection Check ContentsSituate Recorder MainsConnect Recorder to TV Video ConnectionConnect Recorder to Mains Back of RecorderIf you are referring to the front display panel Auto Set UpIf you are referring to the on-screen display Language Code Press %Þ to select CH - and press OK or # Preset DownloadPress %Þ to move Highlight bar pointer to Link and press OKLanguage for the on-screen display If both auto channel set and auto clock set have failedJust Clock Just Clock onScreen LanguageOn-Screen Displays ENABLE/DISABLE ON-SCREEN DisplaySelect Power Save Power Save ModeMode Return to Normal ScreenAccess Mode SET Screen Access Main Menu ScreenLink Functions Return to Normal Screen Colour System SetAbout Ntsc Playback Press %Þ to move the highlight bar pointer toLoad a Cassette Basic PlaybackPoint Start PlaybackPause During Playback Playback FeaturesStill Picture/Frame-By-Frame Playback Press PauseActivate HIGH-SPEED Search Adjust TrackingOverride Automatic Tracking ManuallyIndex Search Activate Index SearchDigital 3R S-VHS/VHS Mode Only Digital TBC/NR S-VHS/VHS Mode OnlyRepeat Playback Soundtrack Selection D-VHS Mode Soundtrack Selection S-VHS/VHS ModeDuring Playback Basic Recording Recording Mode Compatibility Of Cassettes And Recording ModeEngage ITR Mode Recording FeaturesSelect Channel to Watch Start RecordingSET Counter Display Reset CounterDisplay Remaining Time Elapsed Recording Time IndicationVHS Super VHS And VHS Receiving Stereo And Bilingual Programmes Audio Rec Mode Setting D-VHS Mode OnlyTo Record Stereo And Bilingual Programmes A2 S.T. Picture Select B.E.S.T. ModePreparation S.T., then press OK orPlayback RecordingOr press Record on the recorder Timer Programming VHS or VHS mode VHS mode Press STD/LS3Satellite Tuner Users Start Time Express Timer ProgrammingTime Timer Mode SET VPS/PDC ModeSET Tape Speed Engage RECORDER’SPress ä or äTIMER Check, Cancel And Replace ProgrammesPress Again to check More information. Each Time you pressFor Example Auto SP→LP Timer S-VHS/VHS Mode OnlySET, then press OK or # Then press OK or #to selectHighlight bar pointer to Mode SET, then press Auto TimerAuto TIMER, then press OK or #to select eitherAutomatic Satellite Programme Recording Prog REC ModeSET Tape Speed Before performing the following stepsNavigation Access Title ScreenLoad a Recorded Cassette Choose a ProgrammeAccess Video Navigation Screen Access Main Menu ScreenCheck Memory Turn OFF NavigationTitle Editing Access VideoEdit Tape Title Enter Character Enter CharacterSelect Category Entering CharacterDelete Tape Data Select Tape TitleDelete Tape Data Data Delete ProgrammeDelete Programme Data To delete, then pressSorting By Tape Number Access Sorting ScreenSorting By Category Sorting By DateSET Remote Control Remote Control FunctionsRemote A/B Code Switching CodeTV/VCR, TV +/- Volume TV Multi-brand Remote ControlSET TV Brand Code Operate TVSET Satellite Tuner Satellite Tuner Multi-Brand Remote ControlBrand Code TV Prog +/-,NUMBER keysControl SET Mode Access Mode SETPreparation For Editing Select PictureEdit From Camcorder If the camcorder has an S-VIDEO output connector DV Sound SettingIf the camcorder has a DV OUT connector Recorder RecorderEdit To Or From Another Video Recorder Recorder Player AV2 Select Setting AV1 Select SettingSynchro Editing Synchro Edit connector Lanc Cable not providedRepeat steps 5 7 as necessary Access Jlip ID NO. SET Screen Access Initial SET ScreenTerminal Jlip Joint Level Interface Protocol Connector SET Jlip ID NumberSimple Connections Connection To Satellite TunerSatellite Tuner Unit Back of TVPerfect Connections Connectors ScartDecoder Cable Basic ConnectionsSelect Input Mode Connecting Using a DecoderConnect Decoder SET TunerRear View Connecting Using a Stereo SystemTuner Set Access Auto CH SETAuto Channel Set View Confirmation Screen Perform Auto Channel SETAccess Confirmation Screen Access Main MenuSelect Band Input ChannelDelete a Channel When Receiving a Scrambled BroadcastChange Station Channel Position Press %Þ @ #until the item you want to move beginsEnter NEW Character TV Station And ID List Perform Tuning Access Manual Channel SET ScreenFine-Tuning Channels Already Stored Select Channel to FINE-TUNENumber Showview SetupEnter Receiving Channel Position Number Guide Program Number SetAccess Clock SET Screen Access Initial SET ScreenClock Set Turn the Recorder onRecorder is preset to receive clock setting Default setting is OFF. Set as desired by pressingSET Just Clock Channel position to the number representingRemote control wont function No power is applied to the recorderPress Play to turn the indicator off Check the cassette Timer Recording Error Code Quest Ions and Answers Ä remain lit on the display panel. Is there Problem?Index Pull the front panel to access covered buttons/connectorsInside View of Front Panel Rear View Display does not show the -2 of -200000. In this If the counter exceeds -20 hours -200000,Case, confirm the counter on the TV screen 80 EN Remote Control LCD PAL-type colour signal and Ccir Recording specificationManual Channel Setting Manual Tracking Express Timer ProgrammingAutomatic Satellite Programme Recording Change Station Channel PositionEx. Francais is selected for Belgium Ex. Deutschland is selectedInternational Telephone Language Code
Top Page Image Contents