Remote Select TALLY/REMOTE-terminal settings

SET-UP FOR MONITOR INSTALLATION (continued)

WHITE BALANCE ADJUST (white balance adjustments)

Before making these adjustments, select the color temperature 9300K or 6500K on MENU.

Adjustment (level)	Function

RED DRIVE (-10,-9…0…+9, +10)	Adjusts the drive level of a red signal component.

GREEN DRIVE (-10,-9…0…+9, +10)	Adjusts the drive level of a green signal component.

BLUE DRIVE (-10,-9…0…+9, +10)	Adjusts the drive level of a blue signal component.

RED CUTOFF (-10,-9…0…+9, +10)	Sets the cut-off voltage of a red signal component.

GREEN CUTOFF (-10,-9…0…+9, +10)	Sets the cut-off voltage of a green signal component.

BLUE CUTOFF (-10,-9…0…+9, +10)	Sets the cut-off voltage of a blue signal component.

REMOTE SELECT (TALLY/REMOTE-terminal settings)

Via the TALLY/REMOTE terminal, the tally lamp can be turned on/off, or a function (selected from display 3 shown on the right) can be operated using an external control.

NOTE

●By making white balance adjustments on SET-UP MENU, ✻

appears to the right of the COLOR TEMP. setting on MENU

(see page 11).

qREMOTE		SELECT r
I NPUT	: A	B
CNTL - 1	: UNDER		SCAN
CNTL - 2	: ASPECT		RAT I O
ENTER	:

INPUT setting indications and selected inputs

❉: indicates when deactivating the remote control via the TALLY/REMOTE terminal

Setting

NOT USE

AÔB

AÔY/C

AÔRGB

AÔCOMPO

BÔY/C

BÔRGB

BÔCOMPO

Y/CÔRGB

Y/CÔCOMPO

RGBÔCOMPO

Indication

Short-circuit

∗

Y/C

RGB

Open-circuit

∗

Y/C

RGB

COMPO.

Y/C

RGB

COMPO.

RGB

COMPO.

CNTL-1/CNTL-2 setting indications and set positions

❉: indicates when deactivating the remote control via the TALLY/REMOTE terminal

Setting Indication

NOT USE

UNDER SCAN

PULSE CROSS

COLOR OFF

BLUE CHECK

EXTERNAL SYNC

ASPECT RATIO

COLOR TEMP.

AUDIO MUTE

Short-circuit

∗

External

16-9

6500

Open-circuit

∗

OFF

Internal

4-3

9300

OFF

[TALLY/REMOTE terminal functions

All controls via TALLY/REMOTE terminal are made by short-circuiting or open-circuiting any pin from Pin 1 to 4 and either Pin 7 or 8 (GND each) of this terminal.

When using this terminal, be sure to short-circuit Pin 5 and either Pin 7 or 8.

GND

					∗1
	To open-circuit				Tally lamp
	To open-circuit	7	6		To turn off
CNTL-1		7	6		To turn off
CNTL-1		8			To turn on	TALLY
		3		1	To turn on
	To	3		1
	To
	short-circuit	5	4
		5	4
		2			To open-circuit	CNTL-2
					To open-circuit	CNTL-2

To short-circuit

To open-circuit

INPUT

To short-circuit

NOTE

●When the TALLY/REMOTE terminal is used, the following functions become deactivated (except when they are set to "NOT USE"):

-Front INPUT SELECT and EXT SYNC switches

-Front UNDER SCAN, PULSE CROSS, COLOR OFF and BLUE CHECK switches

-On-screen MENU’s ASPECT RATIO and COLOR TEMP. functions

-Remote MUTE key

●If a function is applied to both CNTL-1 and CNTL-2, CNTL-1 has priority.

∗1: Pin 6 is DC power output pin. It outputs DC 5 V when the monitor’s power is on. (Do not short-circuit pin 6 directly to ground.)