JVC BM-H1900SU, BM-H1310SU manual Menu Display Chart, ¥ + Menu

Page 21

:0

:0

:0

:0

:

MENU DISPLAY CHART

The initial (default) adjustments/settings are shown in the menus below.

When the monitor was shipped from the factory, the NTSC SETUP had been set to 7.5 and the COMPO. LEVEL to BETA 75.

For PICTURE ADJUST MENU via remote control, see page 18.

MENU

Menu functions

ASPECT	RAT I O		qMENU r
			:4-3
F I LTER	SELECT :COMB
PEAK I NG		FREQ. :2.6MHZ
PEAK I NG		LEVEL:0dB
AFC			:NORMAL
COLOR	TEMP.		:6500
NTSC	SETUP		:7.5
COMPO. LEVEL			:BETA75
qMEMORY MODE r
RGB / COMPO(SDI)			:RGB
ENTER			:

ENTER

Memory-Mode programming

qMEMORY MODE r

Are you sure ?

gYes hthenENTER

gNo h then or

MEMORY MODE + MENU

MENU

Memory-Mode revision menu

qMEMORY MODE REV I SE					ENTER
P I CTURE AD JUSTMENT
P I CTURE AD JUSTMENT
ASPECT	RAT I O		:4-3
F I LTER	SELECT		:COMB
PEAK I NG		FREQ.	:2.6MHZ
PEAK I NG		LEVEL	:0dB
AFC			:NORMAL
COLOR	TEMP.		:6500
NTSC	SETUP		:7.5
COMPO. LEVEL			:BETA75
ENTER			:

ENTER + MENU

Set-up for monitor installation

qSET-UP MENU r				ENTER
S I ZE / CENTER I NG
WH I TE BALANCE AD JUST
WH I TE BALANCE AD JUST
REMOTE	SELECT
REMOTE	SELECT
STATUS D I SPLAY : ON
CONTROL	LOCK : OFF
ENTER	:

Memory-Mode picture adjustments

qMEMORY MODE REV I SE

CONTRAST	:0
BR I GHT	:0
CHROMA	:0
PHASE	:0
ENTER	:

RGB-signal picture size/positioning adjustments

qS I ZE / CENTER I NG r

H. POS I T I ON V. POS I T I ON H. S I ZE

V. S I ZE

ENTER

Memory-Mode revision

qMEMORY MODE REVISE

Are you sure ?

gYes hthenENTER

gNo h then or

ENTER

¥+ MENU

Menu-function resetting

qMENU rRESET
Are you sure ?
gYes hthenENTER	ENTER
gNo h then	or

¥+ MENU + POWER

“Initialize” menu

q IN I T IALIZE MENU r			ENTER
I D NUMBER SET
qSET - UP MENU rRESET
ENTER

White-balance adjustments

qWHITE BALANCE r

RED DRIVE	:0
GREEN DRIVE	:0
BLUE DRIVE	:0
RED CUTOFF	:0
GREEN CUTOFF	:0
BLUE CUTOFF	:0
ENTER	:

Remote-terminal settings

qREMOTE SELECT r

I NPUT	: NOT	USE
CNTL - 1	: NOT	USE
CNTL - 2	: NOT	USE
ENTER	:

ID-number programming				Menu-function standardization
qID NUMBER SET r				qSET-UP MENU rRESET
00		ENTER		Are you sure ?
		ENTER
				ENTER
				ENTER
				gYes hthen
				gNo h then or

21

Image 21

Contents BM-H1310SU Information Safety PrecautionsFeatures ContentsControls and Features Front Terminals and Features Rear RGB/COMPOSDI terminal setting Connection ExampleExternal/internal synchronization To demagnetize the picture tube Basic OperationPhase picture hue Picture AdjustmentsContrast picture contrast Bright picture brightnessPush each switch to on or OFF for video signal control Video Signal ControlsAspect Ratio picture aspect ratio switching Calling up the menu display, selecting an itemFilter Select built-in filter selection Color TEMP. color temperature switching AFC switching of time constant for the AFCNtsc Setup Ntsc set-up level COMPO. Level chrominance level settingRevision of memory mode Variable setting range Memory ModeTo call up SET-UP Menu and select a function SET-UP for Monitor InstallationInput setting indications and selected inputs Remote Select TALLY/REMOTE-terminal settingsCNTL-1/CNTL-2 setting indications and set positions TALLY/REMOTE terminal functionsStatus Display setting the status display to on/off SET-UP for Monitor InstallationPicture Setting Initialization To initialize Menu settings onlyTo initialize both MENU/SET-UP Menu settings Picture adjustments Remote ControlsSound adjustments On-screen menu remote operationTo assign a monitor use remote control To program an ID number use front controlsTo call up an ID number use remote unit Before Calling for Service ¥ + Menu Menu Display ChartRGB / Compo SDI SpecificationsDimensions BM-H1900SU / BM-H1310SU Color Video Monitor