TacT Audio Connect and Optimize Your TacT RCS 2.2X for Enhanced Audio Performance
Page 34

 

 

Tact 2.2X Room Correction Software

 

 

 

Connect your

Your RCS 2.2X must be connected to your computers serial port in order for it to

 

RCS 2.2X to your

communicate with your computer and to run the Quick Setup and correction pro-

 

Computer

cess. Please follow the steps below to connect your RCS-2.2 X to your computer.

 

 

1 - Connect the RS 232 “Input” jack on the back of the RCS 2.2X to your

 

 

computers serial port using the supplied cables and adapters. Your

 

 

computer must have a standard RS 232 serial port with a DB 9 connector.

 

 

NOTE: If you have any Tact digital amplifiers please disconnect their RS232 con-

 

 

nection at this time.

 

 

2 - Turn on your RCS 2.2X.

 

 

3 - Turn on your computer and start the Tact 2.2X Correction System

 

 

Software.

 

 

NOTE: You may receive a communication error message. Please close the

 

 

message window and proceed to the next step.

 

 

4 - Select the “Communication” button on the main software screen to open

 

 

the communication window.

 

 

5 - Under the Operating Mode select “Connect”.

 

 

6 - Under the COM Port section select “COM1”. If you receive an “invalid

 

 

port number” message please try selecting each of the port selections until

 

 

you do not receive this message. If you receive this message on all COM ports

 

 

you may not have a COM port installed on your computer. Please refer to your

 

 

computer manufactures documentation for help to install a COM port.

 

 

7 - To verify that RCS 2.2X is properly connected to the host computer click

 

 

on the “Start” button to perform the communication test. If everything is

 

 

functioning properly you should see the results below. Press the “Stop”

 

 

button after about 15 seconds to stop the test.

 

 

Rx Buf should display “0”.

 

 

Count should have counted in increments of 100.

 

 

Err Count should be “0”.

 

 

If the results are as above select the “Close” button to close the

 

 

communication window. Your RCS 2.2X is now connected to your computer.

 

 

If the results are not as above please go back to step number 6 and select

 

 

another COM port. Then repeat step 7.

 

 

NOTE: If you are still are not passing the communication test you may not have a

 

 

COM port installed on your computer or you may have another device such as a

 

 

modem or hand held PC that may be sharing the COM port on your computer. If

 

 

you have a Tact amplifier attached it may be set to the same address. The RCS re-

 

 

quires a valid COM port that is not being used by any other devices.

 

 

NOTE: You will only have to select the communication port once. The next time

34 Tact Audio

you run the Tact 2.2X software it will remember your settings.

Page 33 Page 35
Image 34
Page 33 Page 35
Contents RCS Blank Tact Audio Page Acknowledgments RegistrationTable of contents Accessories Operating voltage Unpacking the RCSIntroduction True Upgradeability Modular designRCS 2.2X Connections Digital input Digital output 1 main channels Tact AudioSubwoofers RCS 2.2X Connections Digital outputOptional modules RCS 2.2X Connections Analog input Optional DAC module RCS 2.2X Connections Analog outputMicrophone input RCS 2.2X Connections RS-232 interface AC mains input & mains switchPorts Front panel controls Remote Control Volume Block Correction blockFront Panel Display Main screen Tact AudioFront Panel Display Correction menu option Tone controls are disabledSettings Saving MenuStereo Mode menuMono Assigned to each input independently DOUT-FS menuFront Panel Display POL menu Test menuFront Panel Display Display menu CRO menu Options menu AMP menu Attached to the RCSAnd/or daisy chain to link the components Can result in damage to your speakersMsec Front Panel Display Levels menuEnter button Front Panel Display Parametric EQ menu Front Panel Display Parametric EQ Table LinkedFront Panel Display Tone menu TacT 2.2X Room Correction Software Your computer system must meet the following requirementsRCS 2.2X to your Connect yourComputer Quick Setup Before You Begin Getting StartedQuick Setup SelectStep Step Step Update the RCS-2.2 X Firmware Update the Tact-2.2 X Firmware Status ReadyUpdate the Tact-2.2 X Firmware Tact Audio TacT Audio, Inc

RCS 2.2X specifications

TacT Audio, a pioneering name in the audiophile community, has made significant waves with its innovative product: the RCS 2.2X. This digital room correction system is designed to take your audio experience to a new level, making it a must-have for anyone serious about optimizing sound reproduction in their listening environment.

At the heart of the RCS 2.2X is its state-of-the-art digital signal processing technology. This advanced processing capability allows the device to analyze the acoustic characteristics of your room and adjust the audio output accordingly. By using sophisticated algorithms, the RCS 2.2X can correct frequency response deviations caused by room acoustics, ensuring that you experience your music exactly as the artist intended.

One of the standout features of the RCS 2.2X is its ability to provide customized room correction. Unlike many other systems that offer a one-size-fits-all solution, the RCS 2.2X tailors its corrections based on precise measurements taken from your specific listening environment. Utilizing a calibrated microphone, the system performs a series of measurements and graphically represents the room's acoustic challenges. This personalized approach results in a dramatically improved audio experience, with clearer highs, tighter bass, and a more immersive soundstage.

The RCS 2.2X supports high-resolution audio formats, including 24-bit/192kHz PCM, enhancing its compatibility with various digital sources. It features multiple digital and analog inputs, allowing for seamless integration into existing audio setups. This flexibility ensures that both modern and traditional audiophiles can benefit from the enhanced sound quality provided by this device.

In addition to its room correction capabilities, the RCS 2.2X boasts a powerful crossover function that enables users to create multi-channel audio setups with ease. This feature is particularly useful for home theater enthusiasts looking to optimize the performance of their surround sound systems.

Moreover, the RCS 2.2X includes an easy-to-use interface. It provides a user-friendly setup process, making it accessible even for those who may not be technically inclined. The ability to view real-time frequency response graphs further enhances user engagement and understanding of the acoustic adjustments being made.

In summary, the TacT Audio RCS 2.2X is a groundbreaking tool designed to elevate audio quality through advanced digital room correction technology. With its customizable corrections, high-resolution audio support, and versatile connectivity options, it stands out as a leader in the audio enhancement landscape. Whether you're a casual listener or a seasoned audiophile, the RCS 2.2X promises to redefine your listening experience, making every note and nuance resonate like never before.
Top Page Image Contents