5Still Mode
You can freeze the image shown on the TV screen.
Press [STILL] to pause the image shown on the screen.
Still
•The sound output will not be paused.
•If no signal is detected or protected signal is received during still mode, the image remains paused and the sound output will be muted.
•The still function will be released after 5 minutes.
To cancel still mode, press any button except [POWER].
5Switching Each Mode
You can easily switch with the remote control to the DTV (ATSC) and TV (NTSC) or to access external devices when they are connected to the unit.
Press [INPUT SELECT] or [CH K] repeatedly to cycle through the input modes.
TV/DTV channel
5Switching Audio Mode | INTRODUCTION | ||||||||||
This section describes how to switch the audio language. | |||||||||||
| |||||||||||
TV |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |
1 Press [AUDIO] to display the currently selected | PREPARATION | ||||||||||
audio mode. While receiving an MTS broadcast, | |||||||||||
press repeatedly to cycle through the available audio | |||||||||||
channel. |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| 6 |
|
|
|
| |||
|
|
|
|
|
| ||||||
|
|
|
|
| |||||||
|
|
|
| SAP / STEREO |
|
|
|
| |||
When all audio are available | INITIAL | ||||||||||
SETTING | |||||||||||
SAP / STEREO |
|
| SAP / MONO | ||||||||
| |||||||||||
|
|
| SAP / STEREO |
|
|
| |||||
|
|
|
|
|
| ||||||
|
|
|
|
|
| ||||||
When stereo and monaural audio are available | WATCHING | ||||||||||
MONO / STEREO |
|
| MONO / STEREO | ||||||||
|
| ||||||||||
When SAP and monaural audio are available | |||||||||||
TV | |||||||||||
|
|
|
|
|
|
|
|
|
| ||
SAP / MONO |
|
| SAP / MONO |
| |||||||
|
|
| |||||||||
When only monaural audio is available |
| ||||||||||
OPTIONAL | |||||||||||
|
|
| MONO | ||||||||
|
|
| (Cannot be switched) | ||||||||
STEREO |
| : Outputs | SETTING | ||||||||
SAP |
| : Outputs second audio program | |||||||||
|
| ||||||||||
MONO |
| : Outputs |
| ||||||||
| |||||||||||
or
Video1
Video2
Component1
Component2
HDMI1
HDMI2
• The information display will automatically disappear | TROUBLESHOOTING |
in a few seconds. | |
DTV | |
|
1Press [AUDIO] to display the currently selected language and the number of available languages.
| INFORMATION | |
| ||
English 1/3 |
|
•Pressing [CH L] reverses the direction of the mode.
•To use the video or
•To use the video or
•To use the component video input jacks of COMPONENT1 on the unit, select “Component1”.
•To use the component video input jacks of COMPONENT2 on the unit, select “Component2”.
•To use the HDMI1 input jack on the unit, select “HDMI1”.
•To use the HDMI2 input jack on the unit, select “HDMI2”.
2Press [AUDIO] repeatedly to cycle through the available audio languages.
•Available languages differ depending on the broadcast. “Other” is displayed when the audio language cannot be acquired, or the acquired languages are other than English, Spanish or French.
•The information display will automatically disappear in a few seconds.
Note:
• Pressing [AUDIO] does not control external audio devices.
17
EN