Runco VX-33I VX-33i Rear Connector Panel, Service only For future use, RS-232/485 Control Port

Page 24

2.3

VX-33i Rear Connector Panel

Figure 2-3shows the rear connector panel on the VX-33i, and the paragraphs that follow describe them.

10	9	8	7	6	5
		HD3 (VGA / Y-Pb-Pr)
		Pr)-Pb-Y / (VGA HD3

4	3
WIRED REMOTE
REMOTE WIRED

Service port. Not for user access

		HD1 (RCA)
HD2 (BNC)		(RCA) HD1
(BNC) HD2

12

Figure 2-3. Rear Connector Panel

1.HD2 INPUT

Five BNCs for connecting either RGB or component high-definition sources (up to 1080p). The VX-33i automatically detects the input signal resolution.

2.HD1 INPUT

Five RCA-type connectors for either RGB or component high-definition sources (up to 1080p). The VX-33i automatically detects the input signal resolution.

For best results, do not run your DVD player in progressive mode.

Tip

3.SERVICE ONLY For future use.

4.WIRED REMOTE

Wired input from an external remote control or infrared receiver. It is a 3.5-mm, mini phono jack, wired as follows:

Ring = +5V

Tip = IR Input (TTL level) Sleeve = Ground

When an external remote control or infrared receiver is connected

Note to the wired IR input, the IR sensor on the front of the VX-33i is disabled.

5.RS-232/485 CONTROL PORT

A male, 9-pin D-sub connector for interfacing with a PC or home theater automation/control system. (Currently, only RS-232 interface is supported.)

6.12-VOLT (750 mA) TRIGGER OUTPUTS

Connection for up to three (3), 12-volt trigger-controlled devices. These can be

retractable screens, screen masks or the Runco CineWide with AutoScope system.

8	Runco VX-33i Installation/Operation Manual

Image 24

Contents VX-33i Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents Operation Maintenance and Troubleshooting SpecificationsSerial Communications Table of Contents Xiv List of Figures List of Figures Xvi Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Functions VX-33i at a GlanceVX-33i Rear Panel VX-33i Rear PanelPower Input 100 to 240 VAC Connect the VX-33i to power here Left ButtonVX-33i Rear Connector Panel Service only For future useRS-232/485 Control Port Volt 750 mA Trigger OutputsHdmi I 1 / Hdmi II 2 Digital HD3 InputVX-33i Remote Control VX-33i Remote ControlPicture Adjustment Buttons BRT Brightness On / OFFSource Selection Buttons VID S-VideoMemory Preset Buttons Aspect Ratio Selection Buttons169 Lbox LetterboxInstallation Remote ControlQuick Setup Step Procedure For Details, Refer toIf installing a VX-33i/CineWide or VX-33i/CineWide Installation Considerations Installation TypeAmbient Light Throw Range Throw Ratio Inches, with Lens Option 96x54-inchLens Lens Only Anamorphic Minimum Maximum Apollo B 134.40Ceiling Installation Floor InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Folded Optics Folded OpticsInstalling the Primary Projection Lens Other ConsiderationsPage Installing the Optional CineWide Lens Mount Installing the AutoScope Lens Motor VX-33i/CineWide with AutoScopeRemove VX-33i with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Mounting Connector Panel Access Connecting SourceConnections to VX-33i11. Digital DTV RGB or Component Video Connections HD1, HD2 12. Digital DTV RGB or Component Video Connections HD3 DTV or Progressive Component YPbPr SourceAnalog Computer RGB Connections See Figure 13. Analog RGB ConnectionsVideo/Composite Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcRS-232 Controller ConnectionConnecting 12-volt Trigger Outputs toExternal Equipment AutoScope Lens Motor RearConnecting an External IR Connecting to AC PowerReceiver to Rear PanelTurning on the Power Adjusting the Picture OrientationPrimary Lens Adjustments FocusZoom Lens ShiftInstalling and Adjusting the CineWide Anamorphic Lens Assembly to Lens MotorCarriage Plate CineWide With AutoScope or Base19. Attaching the Anamorphic Lens to the Lens Adapter Ring Configure Lens Motor Adjust the AnamorphicAdjusting the Horizontal X Lens Position TriggerPage Anamorphic Lens Top View Adjusting the Geometry Page Using the On-Screen Menus OperationMemory Presets ServiceInput Source Aspect RatioMain Menu Input SourceAspect Ratio Remote Aspect Ratio Control Description Key 169 Select 169 to view 169 DVDsHdtv programs in their Native aspect ratioPicture Remote Aspect Ratio Control Description KeyPicture Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionMemory Presets Memory PresetsInformation InformationCalibration Calibration ISF NightISF Day Gain/Offset Refer to ISF Night Display Color, above Service ServiceHD Format ISF Day/Night presets Maintenance and Troubleshooting Lamp ReplacementFilter Replacement Side Filter Access PanelTroubleshooting Tips Symptom Possible Causes SolutionPage If you are using a PC to communicate with Serial CommunicationsCommand Description Response Input Selection CommandsAspect Ratio Commands Command Description Response Image Preset Commands Menu Navigation CommandsPicture Adjust Commands Enter or Select buttonCommand Description Response Status Commands Status============================== Resolution 720P60 Page Specifications VX-33i SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsSpecifications are subject to change without notice VX-33i Dimensions VX-33i/CineWide with AutoScope DimensionsSupported Timings Format Resolution Frequency HD 1/HD 2/HD Horizontal Supported? √ = Yes, = NoPage Page 020-1002-00 rev. a September