Runco VX-33I operation manual Installation, Remote Control

Page 29

3. Installation

To install batteries in the remote control, press up on the battery cover retainer clip and lift off the cover. Install the two AAA batteries with the correct polarity and then replace the cover.

•Make sure that the battery polarities are correct when installing the batteries.

•Do not mix an old battery with a new one or different types of batteries.

•If you will not use the remote control for a long time, remove the batteries to avoid damage from battery leakage.

•Make sure that there is nothing obstructing the infrared beam between the remote control and the IR receiver on the projector.

•If the effective range of the remote control decreases, or it stops working, replace the batteries with new ones.

•The remote control may fail to operate if the infrared remote sensor is exposed to bright sunlight or fluorescent lighting.

•Ambient conditions may possibly impede the operation of the remote control. If this happens, point the remote control at the projector, and repeat the operation.

3.1

Remote Control

Notes on Batteries

Notes on Remote Control Operation

Runco VX-33i Installation/Operation Manual

13

Image 29

Contents VX-33i Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation Serial Communications Maintenance and TroubleshootingSpecifications Table of Contents Xiv List of Figures List of Figures Xvi About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories VX-33i at a Glance Controls and FunctionsVX-33i Rear Panel VX-33i Rear PanelLeft Button Power Input 100 to 240 VAC Connect the VX-33i to power hereService only For future use VX-33i Rear Connector PanelRS-232/485 Control Port Volt 750 mA Trigger OutputsHD3 Input Hdmi I 1 / Hdmi II 2 DigitalVX-33i Remote Control VX-33i Remote ControlOn / OFF Picture Adjustment Buttons BRT BrightnessSource Selection Buttons VID S-VideoAspect Ratio Selection Buttons Memory Preset Buttons169 Lbox LetterboxRemote Control InstallationIf installing a VX-33i/CineWide or VX-33i/CineWide Quick SetupStep Procedure For Details, Refer to Ambient Light Installation ConsiderationsInstallation Type 96x54-inch Throw Range Throw Ratio Inches, with Lens OptionLens Lens Only Anamorphic Minimum Maximum Apollo B 134.40Floor Installation Ceiling InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Folded Optics Folded OpticsOther Considerations Installing the Primary Projection LensPage Installing the Optional CineWide Lens Mount Remove Installing the AutoScope Lens Motor VX-33i/CineWide withAutoScope VX-33i with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Mounting Connecting Source Connector Panel AccessConnections to VX-33i11. Digital DTV RGB or Component Video Connections HD1, HD2 DTV or Progressive Component YPbPr Source 12. Digital DTV RGB or Component Video Connections HD313. Analog RGB Connections Analog Computer RGB Connections See FigureDVD Player, VCR Satellite Receiver Laser Disc etc Video/Composite Video Connections See FigureConnection RS-232 ControllerTrigger Outputs to Connecting 12-voltExternal Equipment AutoScope Lens Motor RearConnecting to AC Power Connecting an External IRReceiver to Rear PanelAdjusting the Picture Orientation Turning on the PowerFocus Primary Lens AdjustmentsZoom Lens ShiftAssembly to Lens Motor Installing and Adjusting the CineWide Anamorphic LensCarriage Plate CineWide With AutoScope or Base19. Attaching the Anamorphic Lens to the Lens Adapter Ring Adjust the Anamorphic Configure Lens MotorAdjusting the Horizontal X Lens Position TriggerPage Anamorphic Lens Top View Adjusting the Geometry Page Operation Using the On-Screen MenusService Memory PresetsInput Source Aspect RatioAspect Ratio Main MenuInput Source Select 169 to view 169 DVDs Remote Aspect Ratio Control Description Key 169Hdtv programs in their Native aspect ratioPicture PictureRemote Aspect Ratio Control Description Key Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionMemory Presets Memory PresetsInformation InformationISF Day CalibrationCalibration ISF Night Gain/Offset Refer to ISF Night Display Color, above HD Format ServiceService ISF Day/Night presets Lamp Replacement Maintenance and TroubleshootingSide Filter Access Panel Filter ReplacementSymptom Possible Causes Solution Troubleshooting TipsPage Serial Communications If you are using a PC to communicate withAspect Ratio Commands Command Description ResponseInput Selection Commands Menu Navigation Commands Command Description Response Image Preset CommandsPicture Adjust Commands Enter or Select buttonStatus Command Description Response Status Commands============================== Resolution 720P60 Page VX-33i Specifications SpecificationsSpecifications are subject to change without notice Home Theater Calibration SpecificationsIndustry-Standard Specifications VX-33i/CineWide with AutoScope Dimensions VX-33i DimensionsSupported Timings Horizontal Supported? √ = Yes, = No Format Resolution Frequency HD 1/HD 2/HDPage Page 020-1002-00 rev. a September