Runco VX-33I Connecting 12-volt, Trigger Outputs to, External Equipment, Rear Panel

Page 50

Connecting 12-volt ➤	If your VX-33i is equipped with a CineWide with AutoScope system, connect the
Trigger Outputs to	AutoScope lens motor to a 12-volt trigger output on the VX-33i; see Figure 3-16.
External Equipment	Similarly connect other 12-volt trigger-activated equipment (such as retractable screens or

	screen masks) to the other trigger outputs.
	For more information on using the 12-volt triggers, refer to Triggers on page 58.

AutoScope Lens Motor (Rear)

Power	AC Input
Switch

3.5-mm mini plug

Retractable Screen or other

12-volt trigger-activatedSleeve = Ground

device

Tip = +12V

Rear Panel

HD1 (RCA)

(RCA) HD1

Figure 3-16. 12-volt Trigger Output Connections

34	Runco VX-33i Installation/Operation Manual

Image 50

Contents VX-33i Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents Operation Serial Communications Maintenance and TroubleshootingSpecifications Table of Contents Xiv List of Figures List of Figures Xvi Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Functions VX-33i at a GlanceVX-33i Rear Panel VX-33i Rear PanelPower Input 100 to 240 VAC Connect the VX-33i to power here Left ButtonRS-232/485 Control Port VX-33i Rear Connector PanelService only For future use Volt 750 mA Trigger OutputsHdmi I 1 / Hdmi II 2 Digital HD3 InputVX-33i Remote Control VX-33i Remote ControlSource Selection Buttons Picture Adjustment Buttons BRT BrightnessOn / OFF VID S-Video169 Memory Preset ButtonsAspect Ratio Selection Buttons Lbox LetterboxInstallation Remote ControlIf installing a VX-33i/CineWide or VX-33i/CineWide Quick SetupStep Procedure For Details, Refer to Ambient Light Installation ConsiderationsInstallation Type Lens Throw Range Throw Ratio Inches, with Lens Option96x54-inch Lens Only Anamorphic Minimum Maximum Apollo B 134.40Vertical and Horizontal Ceiling InstallationFloor Installation PositionHorizontal Lens Shift Example only Folded Optics Folded OpticsInstalling the Primary Projection Lens Other ConsiderationsPage Installing the Optional CineWide Lens Mount Remove Installing the AutoScope Lens Motor VX-33i/CineWide withAutoScope VX-33i with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Mounting Connections to Connector Panel AccessConnecting Source VX-33i11. Digital DTV RGB or Component Video Connections HD1, HD2 12. Digital DTV RGB or Component Video Connections HD3 DTV or Progressive Component YPbPr SourceAnalog Computer RGB Connections See Figure 13. Analog RGB ConnectionsVideo/Composite Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcRS-232 Controller ConnectionExternal Equipment Connecting 12-voltTrigger Outputs to AutoScope Lens Motor RearReceiver to Connecting an External IRConnecting to AC Power Rear PanelTurning on the Power Adjusting the Picture OrientationZoom Primary Lens AdjustmentsFocus Lens ShiftCarriage Plate CineWide Installing and Adjusting the CineWide Anamorphic LensAssembly to Lens Motor With AutoScope or Base19. Attaching the Anamorphic Lens to the Lens Adapter Ring Adjusting the Horizontal X Lens Position Configure Lens MotorAdjust the Anamorphic TriggerPage Anamorphic Lens Top View Adjusting the Geometry Page Using the On-Screen Menus OperationInput Source Memory PresetsService Aspect RatioAspect Ratio Main MenuInput Source Hdtv programs in their Remote Aspect Ratio Control Description Key 169Select 169 to view 169 DVDs Native aspect ratioPicture PictureRemote Aspect Ratio Control Description Key Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionInformation Memory PresetsMemory Presets InformationISF Day CalibrationCalibration ISF Night Gain/Offset Refer to ISF Night Display Color, above HD Format ServiceService ISF Day/Night presets Maintenance and Troubleshooting Lamp ReplacementFilter Replacement Side Filter Access PanelTroubleshooting Tips Symptom Possible Causes SolutionPage If you are using a PC to communicate with Serial CommunicationsAspect Ratio Commands Command Description ResponseInput Selection Commands Picture Adjust Commands Command Description Response Image Preset CommandsMenu Navigation Commands Enter or Select buttonCommand Description Response Status Commands Status============================== Resolution 720P60 Page Specifications VX-33i SpecificationsSpecifications are subject to change without notice Home Theater Calibration SpecificationsIndustry-Standard Specifications VX-33i Dimensions VX-33i/CineWide with AutoScope DimensionsSupported Timings Format Resolution Frequency HD 1/HD 2/HD Horizontal Supported? √ = Yes, = NoPage Page 020-1002-00 rev. a September